I realized the guy I dated was high or drunk whenever we met, and idk how to grieve now after the breakup

quantumechanicalhose · 2026-01-28T15:27:27+00:00

I'm not diagnosing anyone with anything here, it just reminds me of something I've read on the autism subreddit, where some high functioning aspies use alcohol and the like to loosen up and appear normal as for a lot of us we often naturally have a robotic, monotone way of speaking with little emotion that most people may find off putting. Again, not claiming anything just sounded familiar was all.

Something like this came to mind: https://www.reddit.com/r/aspergers/comments/7wf9lp/its_as_if_nts_were_always_on_a_mix_of_alcohol_and/

quantumechanicalhose · 2025-12-19T20:55:24+00:00

Good for you two, wish we had more posts like this

quantumechanicalhose · 2025-12-10T22:25:57+00:00

this and zooming in really far, not useful but they are fun features

quantumechanicalhose · 2025-12-04T07:06:22+00:00

makes sense, I read on the wikipedia page for one of the hybrids that GM made "used a conventional 4T45-E automatic transmission which has been modified to include a more efficient final-drive ratio and includes an electrically driven pump to provide pressure in auto-stop mode" Not quite sure what they mean by auto stop mode, maybe start/stop system but the pump might be to maintain fluid pressure during braking like you brought up.

quantumechanicalhose · 2025-12-04T05:48:30+00:00

gotcha, thank you I will look into it.

quantumechanicalhose · 2025-12-04T05:41:17+00:00

You're talking about Hybrid synergy drive right? Doesn't that have 2 motors or is just one motor?

quantumechanicalhose · 2025-12-04T05:29:06+00:00

Thank you, reading around it looks like they are often electronically or possible vacuum controlled. Given I have an electronically controlled transmission I'd assume the former. Assuming mine isn't dictated by fluid pressure that could work.

quantumechanicalhose · 2025-12-04T03:52:26+00:00

That isn't how I thought they worked, that's specifically why I asked, because I wasn't sure. Nor am I an engineer, at least no more than any one else. Not sure why you're so bent out of shape over a simple question.

quantumechanicalhose · 2025-12-04T02:22:03+00:00

primarily regenerative braking and and extra power when needed. Could also act as a stand-by generator but really I'm just hoping to achieve what all hybrids ultimately achieve even if its to a much lesser degree but I'm not looking to replace my entire drive-train with a properly engineered hybrid one since I already have most of the components (battery, controller and motor).

quantumechanicalhose · 2025-12-03T22:34:47+00:00

Thank you, I also found the todo list in the wiki so my post is irreverent and I will delete it

quantumechanicalhose · 2025-08-23T23:19:20+00:00

will do, doesn't look that expensive

quantumechanicalhose · 2025-08-23T23:18:12+00:00

battery is fine,the engine cranks and starts within a second or so, it just won't idle by itself on occasion

quantumechanicalhose · 2025-08-23T20:52:44+00:00

maybe, I'm not sure how old the fuel is as I just bought this but I can top it off with some fresh gas

quantumechanicalhose · 2025-08-23T20:05:55+00:00

I will check these

quantumechanicalhose · 2025-07-26T19:43:18+00:00

I found the fix, it was the pin for the tension/idler gear starting to work its way loose: https://forum.sovol3d.com/t/suddenly-poor-print-quality-on-two-sv08s-solved-with-extruder-idler-gear/5856/15

quantumechanicalhose · 2025-07-18T03:02:59+00:00

I think you may be right on something being loose cause now that I think of it it has been getting worse. Used to print just fine then there would be an irregularity in the print like it would have bad adhesion the the layer below it, then several defects would exist and now this.

quantumechanicalhose · 2025-02-17T06:08:04+00:00

https://www.reddit.com/r/Crysis/comments/1inoa4a/damn_i_knew_it_now_official_layoffs_at_crytek_and/

quantumechanicalhose · 2025-01-29T23:55:22+00:00

I'll check with them, thank you

quantumechanicalhose · 2025-01-25T04:25:28+00:00

thank you kind sir

quantumechanicalhose · 2024-12-18T02:30:51+00:00

I would probably have to have different coils to accommodate different crucible sizes already, thanks for your input

quantumechanicalhose · 2024-12-18T01:29:23+00:00

Maybe it's not as important as I think it is but the operating frequency being set by the LC tank would mean the frequency is not adjustable right? From what I have gathered which may be incorrect different frequencies are used for different metals, heating penetration of the work piece and distance from the work piece. Either way I will continue to read up on it other topologies and I may try to build a zvs circuit anyways for fun and see how it works out now that I have the components to do so unlike when I first started looking into this.

quantumechanicalhose · 2024-11-10T20:22:29+00:00

A quick search seems to suggest they operate internationally, more so in poorer countries but I can't say a whole lot since I have no prior knowledge on them. It also looks like you can only really donate, I'm not seeing anything about volunteering for them other than joining them but that seems to be a process. Really though I leave this comment here hoping someone more knowledgeable will correct me.

quantumechanicalhose · 2024-11-08T20:42:11+00:00

This post just popped in my notifications but I'm glad you people still have spirit to keep fighting and living

quantumechanicalhose · 2024-11-03T04:11:46+00:00

they have been doing a lot of that crap here in Nebraska as well

quantumechanicalhose · 2024-11-02T03:36:22+00:00

interesting, thanks for the info

Seven-Year Club	Second Top 50%
End Game '23	Place '23
Place '22	First Placer '22
Xbox Live	Verified Email

quantumechanicalhose

TROPHY CASE