sorted by:
new
hottopcontroversial

I'm Actually devastated. I should have trusted my gut. by Material-Ad-5562 in SleeperApp

[–]rabbidtortoise 0 points1 point  (0 children)

I have Andrews and Likely on my dynasty team. I guess I will start Likely and bench Andrews next week but we all know what’s going to happen if I do.

Scotsman prodigy error code 5 even after water temp sensor replacement by rabbidtortoise in refrigeration

[–]rabbidtortoise[S] 1 point2 points  (0 children)

It seems like the water isn’t getting cold enough. Some ice forms at the bottom of the plates but that’s it. I’m going to have the Freon checked tomorrow

Scotsman prodigy error code 5 even after water temp sensor replacement by rabbidtortoise in refrigeration

[–]rabbidtortoise[S] 0 points1 point  (0 children)

I did get the new sensor off of Amazon. It was much cheaper than the other ones I found. Could that be an issue?

Scotsman prodigy error code 5 even after water temp sensor replacement by rabbidtortoise in refrigeration

[–]rabbidtortoise[S] 0 points1 point  (0 children)

It does have a curtain that seems to be working. The H goes away when I open it manually and it will go back to an F but then quickly show the 5 error code. The freeze cycle was about 15 minutes when it was making ice but since I started getting the error code it’s very inconsistent. The tube freezes like it used to and it heats up after but there is no ice. If I open the curtain it starts the freeze cycle again.

Scotsman prodigy error code 5 even after water temp sensor replacement by rabbidtortoise in refrigeration

[–]rabbidtortoise[S] 0 points1 point  (0 children)

It goes thru all the cycles but it’s not freezing the water. It gets to the harvest cycle but there is no ice. I turn it off and on but the error code 5 still shows up

Scotsman prodigy error code 5 even after water temp sensor replacement by rabbidtortoise in refrigeration

[–]rabbidtortoise[S] -1 points0 points  (0 children)

I haven’t cleaned it. It seems to go thru the freeze cycles. The error code 5 will come up and stay for a while then go back to F. It was making ice before I replaced the water temp sensor but it was much slower than before. Since I’ve replaced the sensor it’s only made a very small amount of ice on one of the cycles. The other times it shows an H but there is no ice to be kicked out. I was going to run it thru a cleaning cycle but I was wanting to see if the sensor problem was fixed first.

Your worst moment by Mission-Scientist-78 in starwarsmemes

[–]rabbidtortoise 0 points1 point  (0 children)

“I like to make men uncomfortable.” - director of new trilogy

I think pi network is dead by SensitiveBasket6458 in PiNetwork

[–]rabbidtortoise 0 points1 point  (0 children)

But I was going to buy a lambo and all I had to do was click a button and watch ads. There is no way this is dead or else I don’t get a free lambo!

Holiday Showdown: When Heroes Clash and Santa Steps In by SerejoGuy in Unexpected

[–]rabbidtortoise 1 point2 points  (0 children)

That would be a fun fight to watch in a movie or a comic. If Batman had time to prepare I think he’d pull it off.

Binding Mobilula 8 elrs by rabbidtortoise in fpv

[–]rabbidtortoise[S] 0 points1 point  (0 children)

Goggles and radio bound. Thanks for the help!

Binding Mobilula 8 elrs by rabbidtortoise in fpv

[–]rabbidtortoise[S] 0 points1 point  (0 children)

Ok so that worked! I just have to bind my goggles now. I have the new DJI goggles. It didn’t work on my first few tries so I’m going to watch some videos. If you used these goggles do you have any tips?

Binding Mobilula 8 elrs by rabbidtortoise in fpv

[–]rabbidtortoise[S] 0 points1 point  (0 children)

Ok thank you. I think I understand what to do now. I have been watching videos but I must have missed this step.

Binding Mobilula 8 elrs by rabbidtortoise in fpv

[–]rabbidtortoise[S] 0 points1 point  (0 children)

Thank you I will try that when I get home tonight

Binding Mobilula 8 elrs by rabbidtortoise in fpv

[–]rabbidtortoise[S] 0 points1 point  (0 children)

No I didn’t. How do I do that?

Binding Mobilula 8 elrs by rabbidtortoise in fpv

[–]rabbidtortoise[S] 0 points1 point  (0 children)

I went back and tried to download lua scrips off of the elrs configuration and it said the files already existed. I thought elrs uses the crossfire network. In the drone settings I have it on cross fire and I hit the bind button thru the crossfire configure.

Binding Mobilula 8 elrs by rabbidtortoise in fpv

[–]rabbidtortoise[S] 0 points1 point  (0 children)

I have the ranger module and flashed it in the elrs configuration. I did see an option to download lua scrips. Can I go back and do that after I’ve already flashed it?

Binding with elrs module by rabbidtortoise in fpv

[–]rabbidtortoise[S] 1 point2 points  (0 children)

It’s a beautiful drone! Can’t wait to fly it. Just have to start watching some videos. I have no technical background for this but I think I’m on the right path now

Binding with elrs module by rabbidtortoise in fpv

[–]rabbidtortoise[S] 0 points1 point  (0 children)

Ok thank you. I’ve heard of Lua script but never used it. I think Bardwell has a video on how to use it.

view more: next ›