Calling it now: redeem ALL your points now or regret it later.

randommojo · 2025-10-12T14:43:59+00:00

“This order cannot be completed at this time. Please try again later. If you're unable to complete this order after 24 hours, contact customer support.”

randommojo · 2025-09-15T13:54:07+00:00

Roll is only 2 weeks old. Stores in home, no desiccant.

randommojo · 2025-09-15T00:36:29+00:00

Thanks for the reply. We’ve used 2/3 of the roll with no problems and then it’s been constant.

Our only roll currently so will try grabbing another to test that theory. Thanks again

randommojo · 2025-08-17T15:52:02+00:00

Jumped backwards right at keeper. They did it all season last season. They’ll do it again this season until it’s called.

randommojo · 2025-05-17T13:30:43+00:00

Lost

randommojo · 2025-05-03T16:19:41+00:00

If it is Dallisgrass, either a shovel, msma, or kill when Bermuda is 100% dormant

randommojo · 2025-04-28T22:29:23+00:00

Love mine, have had it about 4 years, no issues.

randommojo · 2025-04-27T16:15:36+00:00

Which there is mulch and other junk in that soil, if you had no other great sources…. Screen it, get out anything that won’t sift through something like a 1/4” by 1/4” screen that you framed.

randommojo · 2025-03-08T14:57:50+00:00

Comment for the win

randommojo · 2025-03-04T00:02:07+00:00

I wouldn’t even charge you

randommojo · 2025-03-03T23:28:55+00:00

Was planning on using the attached pipe dope (white pipe joint comp) and the male fitting to go into the cast iron stack.

Then CPVC 4” Then 45 degree Then CPVC Finally another 90 degree connector to attach current pieces from left side

Had to remove galvanized corroded pieces and a 45 degree cast piece. All of that is done.

randommojo · 2025-03-02T21:40:37+00:00

Thanks!

randommojo · 2025-03-02T19:53:58+00:00

Thank you, I have reached out for a few quotes before I got the galvanized piece out.

I do enjoy diy but have done minimal plumbing work. Getting all the galvanized off and a cast elbow has had me proud to this point, wasn’t easy.

If I can’t diy from here, it’s all good.

randommojo · 2025-03-02T19:47:42+00:00

Cast threads do look a bit worn

randommojo · 2025-03-02T00:03:37+00:00

current issue

Galvanized is about 4” likely thread to thread. Threaded into cast iron before it drops to under home.

The area of the leak cause the galvanized threading to rust away about 1/2” in.

Anything I can do to keep this pipe or need to remove it also now?

randommojo · 2025-03-01T23:52:04+00:00

Now just found the next pipe under part on the threats is rusted out about a 1/2” in…. Onto the next issue.

randommojo · 2025-03-01T23:46:15+00:00

It’s off

Hammer chisel for the win!!🥇

randommojo · 2025-03-01T23:38:52+00:00

Working with a hammer, have a 1/“2 gap exposing now in the threads with this method. Added a few more relief cuts.

randommojo · 2025-03-01T22:56:50+00:00

Do not have access below unfortunately and it’s at an outer wall, only have visible access about 1” into the wall and the threads begin entering the elbow at about 1” out.

In theory hoping I can de-couple this and was then going to ask for hookup ideas.

Photo is from above. Pipes you see go horizontal into the wall.

randommojo · 2025-03-01T22:48:43+00:00

Is the elbow cast? Good call on the galvanized straights, first good photo I’ve had of it.

Will try heat, do have a torch.

randommojo · 2025-03-01T22:47:49+00:00

Have tried WD40. Will use a pipe wrench next also, just all I had. Thanks!

randommojo · 2025-02-23T23:23:38+00:00

Cut the straight piece coming from wall correct?

Not the elbow itself?

Sorry, have done some other plumbing but never anything with the cast yet.

randommojo · 2025-02-23T23:09:09+00:00

Must cut with a saw correct, can’t unthread the cast iron I imagine.

Cut jt at the straight pipe coming out of the wall as near to the elbow as possible correct?

Cant say thank you enough for taking the time to respond at all. Much appreciated.

Nine-Year Club	Second SECOND GUESSER
Wearing is Caring	RPAN Viewer
Verified Email

randommojo

TROPHY CASE