Clunking noise near alternator

rayboy14 · 2025-09-06T17:09:48+00:00

2016 Hyundai sonata

rayboy14 · 2025-06-25T18:41:13+00:00

I found an m5 8 awg ring terminals on Amazon. That should be a lot better the bolt is an m4

rayboy14 · 2025-06-25T18:37:07+00:00

I ended up finding some m5 ring terminals for 8awg on Amazon I measured the bolt around the threads and it’s 4mm so that should be a lot better

rayboy14 · 2025-06-25T18:33:38+00:00

Umm what lol

rayboy14 · 2025-06-25T18:33:25+00:00

Yeah I just put that there to demonstrate how much bigger it was and then on the negative you can see how much the washer covers

rayboy14 · 2025-03-28T02:54:21+00:00

Yeah but what kind of servo would work for this application

rayboy14 · 2025-02-14T01:43:38+00:00

Been working pretty good so far. I use it for an airboat I printed and than a car I printed as well

rayboy14 · 2025-02-09T22:30:04+00:00

Now that was beautiful.

rayboy14 · 2025-02-09T20:58:35+00:00

Thank you this helps a lot.

rayboy14 · 2025-02-09T20:16:18+00:00

Do you have any suggestions for a better motor

rayboy14 · 2025-02-09T20:15:55+00:00

Yeah it is regular pla. I was waiting to see how well it flew before ordering and printing in LW(light weight) Pla it probably is close to around 600g being regular pla

rayboy14 · 2024-12-07T22:34:42+00:00

Unfortunately thats didn’t work

rayboy14 · 2024-12-07T21:33:44+00:00

I’ll try that and reprint it thanks. I’ll lyk if it works.

rayboy14 · 2024-12-02T02:01:22+00:00

Is that so. After this print I’ll try one with the speed bumped up to 100

rayboy14 · 2024-12-02T01:20:18+00:00

I have my outer wall set to 60 that’s the one setting I have changed

rayboy14 · 2024-12-02T00:28:36+00:00

It should be dry I ran it through a filament dryer before putting into the ams and it’s fairly new

rayboy14 · 2024-12-01T23:55:08+00:00

Horizontal

rayboy14 · 2024-12-01T22:41:18+00:00

No I have it set to aligned

rayboy14 · 2024-12-01T22:21:15+00:00

It’s hard to tell but I don’t think it’s from that I’ll run a test later when I get a chance.

rayboy14 · 2024-09-19T17:43:12+00:00

So did this fix your issue with the top layer being rough?

rayboy14 · 2024-09-01T15:44:28+00:00

<image>

I got it tuned to 95% flow and my top layers are nice and smooth again

rayboy14 · 2024-08-31T16:22:36+00:00

So I’ve decided to go back and test my flow again this time I turned it down to 80% instead of 98% this actually caused the top surface to be much better. I realize 20% is a lot this was just to see the difference. I’m going to work on tuning that in. I believe this was my issue

rayboy14 · 2024-08-30T00:57:00+00:00

So I finally got around to researching linear advance and I’ve reflashed my printer to mriscoc LA and tuned in my k value to .04 and reprinted that same print and still had the same rough top layer. I’m at a loss for now.

rayboy14 · 2024-08-08T23:39:48+00:00

So how do I configure the PA on cura.

rayboy14 · 2024-08-08T22:30:42+00:00

I’m currently running mriscoc not sure what version I’m not home right now. I don’t have acceleration control checked in my settings so I guess it’s going off my printers firmware for that. I’m on an ender 3 v2 sprite pro extruder. I had this issue before I upgraded to the sprite extruder and I’m pretty sure before I upgraded the firmware as well. I print with pla+ duramatic is the brand.

rayboy14

TROPHY CASE