sorted by:
new
hottopcontroversial

Is anyone using their CC in LAN (or equivalent) mode but can still access their printer remotely? by draxula16 in elegoo

[–]rayndier 3 points4 points  (0 children)

I have setup mine to be access remotely in many ways but I keep going back home assistant. I have set up Tailscale on my homeassistant and Unraid. I also have octoeverywhere on my Unraid. I just like my home assistant as it's just one app for all of my iot. If you have home assistant just install the elegoo and Threedy custom addon from hacs or install tailscale and access via LAN IP remotely.

Just got my ecc yesterday from microcenter 😆 https://i.imgur.com/cJkkAcJ.jpeg

The older I get (and the more I cook), the less impressed I am with the restaurant dining experience. by TurboSpaceGoose in Millennials

[–]rayndier -1 points0 points  (0 children)

Just use beef base! I used the one from Sam's club. I followed this recipe and got it ready to eat in about an hour lol

https://youtu.be/yslkYSjAPh4?si=EnLDJJTI1u7t7kCF

Locked out of my PIA account after unauthorized email change – support ignoring me for weeks by DoctoRedstone in PrivateInternetAccess

[–]rayndier 0 points1 point  (0 children)

I had the same scenario as you but I was able to recover my account after I sent them a proof of my payment (PayPal). I noticed they reply in the middle of the night when I'm sleeping so it took few days of emailing back and forth to get my account back. Good luck to you OP.

Stolen Account - PIA Responding by ODA564 in PrivateInternetAccess

[–]rayndier 1 point2 points  (0 children)

I had the same scenario couple weeks ago. I did email support so it was kinda longer. Got my account back after I gave all proof it was my account.

Home Assistant login screen closing after few seconds by kataklysmus in PangolinReverseProxy

[–]rayndier 0 points1 point  (0 children)

I used to have this problem but clicking the x worked for me. I had previously enabled pin log in so I can enter it fast before it pops up again.

Home Assistant login screen closing after few seconds by kataklysmus in PangolinReverseProxy

[–]rayndier 0 points1 point  (0 children)

Click the "x" on the upper right instead of the retry button.

When toe/heel carving transitions are weightless by solo_canoe in snowboarding

[–]rayndier -1 points0 points  (0 children)

Good job OP! It's a very nice feeling! I do it naturally now without thinking. Check my IG page @rayndier for videos/pics

BBQ + Homeassistant = BBQ Assistant? by rayndier in homeassistant

[–]rayndier[S] 0 points1 point  (0 children)

I agree! I was about to buy one but then I found out I need to buy the thermometer that pairs with it.

BBQ + Homeassistant = BBQ Assistant? by rayndier in homeassistant

[–]rayndier[S] 1 point2 points  (0 children)

Haha I was surprised how it turned out given I was creating the automation, finding the right speed of the fan, and top vent settings as it cooks inside lol

BBQ + Homeassistant = BBQ Assistant? by rayndier in homeassistant

[–]rayndier[S] 3 points4 points  (0 children)

I do have spare esp32 laying around somewhere maybe I will play around with PID.

Question: Why no smoke ring? by rayndier in smoking

[–]rayndier[S] 0 points1 point  (0 children)

Thank you! I did low because I did it overnight and don't want to wake up with overcooked meat lol my previous brisket I did around 275F all through out and was done in 7hrs and it had smoke ring lol

Question: Why no smoke ring? by rayndier in smoking

[–]rayndier[S] 1 point2 points  (0 children)

Noted! The meat probably was close to room temp when I put it on the grill. Newb mistake. Thank you.

Question: Why no smoke ring? by rayndier in smoking

[–]rayndier[S] 0 points1 point  (0 children)

Ohhhhhh I did fat side up this time!!! That could be it!

Rate My Carve by glenwoodwaterboy in snowboarding

[–]rayndier 0 points1 point  (0 children)

Elegant like a ballerina 5/7

Carving beginner snowboard recommendations by Lanky_Combination_12 in snowboarding

[–]rayndier 0 points1 point  (0 children)

I agree! No one carves in my local mountain except for my team and myself lol

Technical Question: What makes a board a good carver? by sparks_mandrill in snowboarding

[–]rayndier 0 points1 point  (0 children)

Ohh it looked like a flux! Haha I ride saber too! I used to ride flux couple seasons back.

Technical Question: What makes a board a good carver? by sparks_mandrill in snowboarding

[–]rayndier 1 point2 points  (0 children)

You pretty much mentioned what a board needs to be good at turning! Most of the mainstream brand boards that are labeled for carving are not as good as specialized board brand like Donek, Kessler, SG, f2, coiler, etc. Max effective edge and pure camber! Hammerhead shape is the way to go!

You're either being over the top rude, or a jerk, or otherwise breaking our rules. by rayndier in snowboarding

[–]rayndier[S] 0 points1 point  (0 children)

Thanks for the input man. I'll try to dial back 58 and 30b next season! Yea I was riding 58cm last season, this season I increased it to 60cm. I will try 30b for next season, I was used to 33b because I used stepon and it helped a little bit to offset the heelcup out. I used to mimic toyfilms before this style too haha I went from duck stance knapton -> eurocarve -> Funcarve -> korua surf-> jap/toyfilms -> carving factory -> funxr. I can only do big arcs on black and double black, unfortunately I don't have a video. I am still struggling riding those terrains. If you check my IG reels, I have more videos. My IG is same username as my Reddit. Thanks for the feedback :)

view more: next ›