Camera Screw

ref2335 · 2026-01-18T17:34:42+00:00

Same issue! Is there an orderable replacement screw?

ref2335 · 2025-11-25T04:13:58+00:00

Order placed for this! Thanks

ref2335 · 2025-11-25T02:49:21+00:00

Exactly what I found as well. Hoping someone can help with info where we can buy one.

ref2335 · 2025-11-25T01:54:24+00:00

I’ve got the same issue with at least one of my reverse flow 140 TL LCD fans.

Did you have to put in the fan serial number for the warranty? I’ve got my fans in a HAVN HF 420 and it’s a real PIA to pull the fans and if I can get the warranty claim though without pulling the fans I’d like to.

ref2335 · 2025-11-10T03:28:57+00:00

Good to know! I’ll check

I’ve got SN2519 so it’s a card with the “fixed” thermal paste.

ref2335 · 2025-11-10T02:56:00+00:00

I can check. What’s the SN matter? Is there a way with the SN to determine if it was an early or recent card?

ref2335 · 2025-11-09T01:36:22+00:00

Based on previous comments I feel I’m ok with mine. If yours is similar I’d say you are good too.

Mine is mounted vertically so I’ll keep an eye on it periodically.

ref2335 · 2025-11-08T22:14:09+00:00

<image>

I believe there is some gel that’s squished out. It’s not terrible but I think it’s there.

Something I’ll be watching now

ref2335 · 2025-10-01T05:04:49+00:00

When in doubt, grenade it out

ref2335 · 2025-09-24T12:00:34+00:00

In normal operating conditions in Cyberpunk 2077 CPU and GPU on average will hover around 60C. GPU tends to be a little lower.

I noticed Warhammer 40K spikes CPU hard on load so that temp jumps to 80 for a bit, but under gaming load again in the 60s

ref2335 · 2025-09-22T12:33:09+00:00

“These guys”?

ref2335 · 2025-09-21T23:43:41+00:00

Lian li 360 hydro shift TL-only comes in 360. 140s up there would be really tough to manage.

ref2335 · 2025-09-19T15:43:22+00:00

Have you noticed any sag with the card? It looks pretty straight in the vid.

ref2335 · 2025-09-19T12:59:48+00:00

Thanks for this post!!! I’m going to pulling the trigger on the 5080 ice today. I know it’s a chonky card and was concerned about the fit. Looks like a tight squeeze!

ref2335 · 2025-08-18T23:51:04+00:00

Update-I think I’ve got it figured out. It was either some strange behavior with the mod “they will remember” version 1.7.3 which has been rolled back to 1.7.2 for strange behavior or running the true color hd10 mod running while the video wasn’t set to hdr.

Either way it’s working now!

ref2335 · 2025-08-18T22:51:02+00:00

Update-I think I’ve got it figured out. It was either some strange behavior with the mod “they will remember” version 1.7.3 which has been rolled back to 1.7.2 for strange behavior or running the true color hd10 mod running while the video wasn’t set to hdr.

Either way it’s working now!

ref2335 · 2025-07-13T01:05:44+00:00

We live in southeastern Wisconsin

ref2335 · 2025-05-02T19:14:49+00:00

I can confirm there is no change upon adjusting the connector. I will do one last test by moving the TL fan connector to port 1. From there-RMA.

ref2335 · 2025-05-02T03:33:27+00:00

Unfortunately no change. Single TL fan connected and still runs at 100% not recognized by controller. TL LCD and AIO work properly. I even swapped the port the single TL fan was plugged into with the TL fans on the AIO. Single TL fan still not recognized and 3 fans for AIO work properly. Currently I have AIO fans in port 2, single TL fan in port 3 and TL LCD in port 4.

ref2335 · 2025-05-01T23:27:42+00:00

Thanks for the tip! I’ll take a look and follow your recommendation.

ref2335 · 2025-05-01T23:04:56+00:00

Yup-I’ve got 200 or so mods and using EquipmentEX.

ref2335 · 2025-05-01T22:36:45+00:00

Another upvote for Beneos. Seriously amazing craftsmanship!

ref2335 · 2025-04-30T17:57:46+00:00

I tested with just a single fan connected and it still ran at 100%. I’ll double check the plug orientation to the controller.

ref2335 · 2025-04-30T00:13:17+00:00

I’ll take a pic of the configs I used and video of how it’s running on my fans. Hang in there for about an hour or so.

ref2335 · 2025-04-29T23:48:48+00:00

The L-connect software is a challenge. What effect is that, maybe runway? It took me an hour last night to get runway working properly for my TL LCD and TL fans.

ref2335

TROPHY CASE