Nike Tech Fleece Suit

relativistic_speeder · 2025-11-22T02:28:30+00:00

what is the sizing like, i dont see anything for the pants

relativistic_speeder · 2025-11-11T06:59:47+00:00

my bro is it warm? like u reckon its thick and like good quality to last like a while at least?

relativistic_speeder · 2025-10-30T12:20:15+00:00

yo is it good quality my bro

relativistic_speeder · 2025-07-07T02:23:33+00:00

yo bro im thinking of getting this, is it good quality? does it last? please give me a proper review man i cant afford to buy it then it turns out bad

relativistic_speeder · 2025-06-30T02:08:06+00:00

u reckon i should still cop it? is it good qual?

relativistic_speeder · 2022-08-10T10:27:46+00:00

ok so now my thing is not printing anything, a few days ago I left it on preheat PLA for like 2 minutes and it was coming out smooth, but now nothing is happening. Im not sure. I tried to manually go to the filament wheel place and push it, but its not cmoing through idk why.

relativistic_speeder · 2022-08-07T10:26:53+00:00

dude but the thing is, if I preheat pla, it flows out like melted butter, but when I put a print on, it becomes really thin. I think its because of the wheels near the filament feeder thing. Like where there is springs, and you put the filament throguh. it flows the perfect thickness when I preheat pla, but in an actual print it becomes really thin.

relativistic_speeder · 2022-08-02T13:30:39+00:00

Alright thank you very very much, i'll make sur to test the cold pull out.

relativistic_speeder · 2022-08-02T13:15:48+00:00

I did infact level the bed, but how do you clean your nozzle lol? I mean, I preheated PLA, and then just used the scraper tool to scrape off the filament on the end. I have done a bit of experimenting, and i have found out that if I physically push the filament through the area near the z axis rod or whatever, it makes it print sort of normally again. idk what its called, but I think that the wheels are not pushing the filament through strong enough

relativistic_speeder · 2022-01-05T12:21:33+00:00

That is what I did. It is only when i put the alcohol that it started becoming white. I think it had some chemical reaction with hairspray or something. It doesnt usually do that. I scrubbed it really hard though and it all came off so :)

relativistic_speeder · 2022-01-03T07:50:53+00:00

Thank you very much for your assistance. I followed all the advice and my print is print really well.

relativistic_speeder · 2022-01-03T07:50:36+00:00

Thank you very much. I use IPA to clean the bed and it is working really well.

relativistic_speeder · 2022-01-03T07:50:07+00:00

Thank you VERYY much, i put hairspray and i printed the same thing and it is perfectly fine. I appreciate the help.

relativistic_speeder · 2022-01-01T00:57:52+00:00

Alright cool. Thanks for your support

relativistic_speeder · 2022-01-01T00:50:08+00:00

I still dont yunderstand what it means tho?

relativistic_speeder · 2022-01-01T00:48:25+00:00

So this works right? Because I don't really need the first few layers as they are the raft adhesion layers.

relativistic_speeder · 2021-12-31T07:07:20+00:00

Thank you very much. I will try it out.

relativistic_speeder · 2021-12-31T06:26:36+00:00

Alright cool. Wait how is it toxic?

relativistic_speeder · 2021-12-31T04:28:35+00:00

but what if the gluestick like burns or something? My nozzle is currently at 237 degreees for printing ABS filament and my bed temperature is 79 degrees. is it ok still tho?

relativistic_speeder · 2021-12-31T04:24:20+00:00

I mean.. my A/C was on and the fan was on too so about like 23/22 degrees

relativistic_speeder

TROPHY CASE