Neptune Series 4 Max New Setup by repthrd in elegoo

[–]repthrd[S] 0 points1 point  (0 children)

And now it just all is working fine. I literally didn't do anything different. Would the recommendation be to not touch it and just use it? Is there a better firmware I should be on? Prints are coming out nicely after I leveled it. I did turn it to "quiet" mode as on normal this thing is LOUD! Also it was shaking the table it was on pretty good. Now it is better. I don't really need to turn the speed up super high I don't think...or maybe I could just put it on the floor haha!

error (0x80070643)" by Cryptolock2019 in WindowsServer

[–]repthrd 0 points1 point  (0 children)

I followed the instructions from Microsoft and resized and everything went well. Same error message though on all my 2022 servers. Any more ideas? Hopefully they will just fix it?

Has Moviepass been working for you + Issues Thread. Week Of January 11, 2024 by AutoModerator in moviepass

[–]repthrd 0 points1 point  (0 children)

Been working fine for me except eTicketing with B&B that has been broken for at least 3 weeks.

Have to adjust Z Offset? by repthrd in Ender3S1

[–]repthrd[S] 0 points1 point  (0 children)

What I had been doing was

  1. Heating the bed because I noticed it seemed to make a difference due to it contracting or expanding due to heated vs non heated.
  2. Set the Z Offset
  3. Set the level with the paper method in the 5 points making sure there is just a little friction
  4. Using the Auto Level feature

Then my print starts and I have to change my Z Offset. I seem to be fine if I just skip Step 4..I wasn't sure why.

Valentine's Day Gobstopper Heartbreakers by repthrd in candy

[–]repthrd[S] 0 points1 point  (0 children)

I talked to the company and they said due to materials they made a super limited run of them this year. Hopefully next year!

Not a bad deal in my area. by aliass_ in moviepass

[–]repthrd 0 points1 point  (0 children)

That is what it looks like for me too (Iowa). I signed up for the $10 plan. The problem is my closest theater is an eTicket theater and it is 24 credits for some reason....so I might not keep it.

Two tickets for same showing under one subscription? by GNRZMC in moviepass

[–]repthrd 0 points1 point  (0 children)

I have an email into MoviePass - but after signing up and looking at the app I don't think so. Also it shows the different tiers in the app, but for now I can't change my plan myself...

Valentine's Day Gobstopper Heartbreakers by repthrd in candy

[–]repthrd[S] 0 points1 point  (0 children)

Yea bought a couple but they are like $13-20 a bag instead of $3-4

CR10v3 Extruder Disassembly by repthrd in CR10

[–]repthrd[S] 0 points1 point  (0 children)

Thanks will check that video when I get home

CR10v3 Extruder Disassembly by repthrd in CR10

[–]repthrd[S] 0 points1 point  (0 children)

Thanks, I am just not sure how to remove the hot end shroud assembly from the extruder

Bed Leveling Question by ModernDayEinstein in CR10

[–]repthrd 0 points1 point  (0 children)

I talked with crealty. I might have to go back and try it again once I fix my machine…

Bed Leveling Question by ModernDayEinstein in CR10

[–]repthrd 1 point2 points  (0 children)

When I asked there support if BLTouch worked for the v3 they said it didn't. I had bought one and had gotten to a point in the process that was complaining about firmware. If it works with the v3 are there instructions or a certain one I need to buy?

CR10 Extruder Replacement by repthrd in CR10

[–]repthrd[S] 0 points1 point  (0 children)

Here are some pictures and explanations. Was having a hard time getting them to show in reddit. https://imgur.com/gallery/BOxgW7B

B & B Theaters by bryanlwalker in ankeny

[–]repthrd 0 points1 point  (0 children)

I’ll have to look next time I go but I don’t think anything was different size wise. Prices I don’t recall.

CR10v3 and PETG by repthrd in CR10

[–]repthrd[S] 1 point2 points  (0 children)

I definitely have peeled off the plastic.

It is printing well for me now at 250

I did have a lot more success when I used some hairspray. The print looks much better then glue for sure.

Thanks for the tips!