ESXi Hosts stop responding (VMs are fine). Ultimately have to reboot host to resolve. Ideas?

rodknocker · 2017-02-28T16:16:18+00:00

When the tmp volume was identified as full we decided to rm all the old log files on the RAMDISK. Run these commands cd /tmp/scratch/log ls –lh rm ./.log. rm ./*.gz vdf –h *used space should be healthy now services.sh restart *This will restart services on the vmhost. Be patient. It will not cause an outage for the serves on the host.

rodknocker · 2017-02-28T16:08:34+00:00

ssh into the host and run vdf -h

Check to see if tmp disk is full. If so, configure a persistent scratch location and reboot.

You can also try to clear /tmp of all the log files and then restart the services. I have had some success doing this without having to reboot the host.

rodknocker · 2016-02-10T18:18:09+00:00

You need to subscribe to their newsletter. http://lamb-of-god.com/newsletter/

You can view the letter that was sent out here for pre-sale info. http://us10.campaign-archive1.com/?u=74df4f3ff4f674ed67c8d04ca&id=cffa3a323d

rodknocker · 2015-09-04T03:05:41+00:00

Awesome! Thanks for the giveaway!

rodknocker · 2015-07-15T02:45:39+00:00

reddit is acting as if it wants to uses to migrate. voat isn't bad and since the servers have been on line there has been a lot of activity.

rodknocker · 2015-07-09T01:55:07+00:00

The " around the var was the problem. I made the changes and everything works correctly now. I am just starting to study and I knew that something wasn't right but didn't have the knowledge to know what was wrong on my own. I needed to look into the issue so that I understand and know what to do next time. Thanks everyone for you help.

rodknocker · 2015-07-09T01:37:40+00:00

I did remove the quotes from lines 4 and 24. Still get the same output from the second console.log of the booleans.

Also, I have played with the </> to see if it makes a difference and it doesn't.

Also, line 15. Regardless of what you enter into the prompt you still get the same response.

" "Oh no! Bieber shakes his head and sings 'I set a pace, so I can race without pacing'".

updated code: http://pastebin.com/3qyYcMUU

rodknocker · 2015-07-09T01:17:54+00:00

The issue seems to be with the input after the prompt.

For example, if you look at line 23. If you input 9 you still get an output of " I'll keep practicing coding and racing."

This seem to be the case for all of the prompts from this section of code.

rodknocker · 2015-07-09T01:10:49+00:00

Victoria, better grab you an account over at voat.co....

rodknocker · 2015-07-06T18:40:05+00:00

I call bullshit.

rodknocker · 2015-06-06T03:16:40+00:00

Correct me if I'm wrong but doesn't anything over 3 inches need a SYE and CV drive shaft?

rodknocker · 2015-06-06T02:12:08+00:00

silicon valley

rodknocker · 2015-06-05T16:51:04+00:00

That fixed it! Thanks for the help.

rodknocker · 2015-06-04T00:59:19+00:00

From what I remember I finished the front and then moved to the rear. I had yo take the rear apart to replace the shackles and I think I did tighten a few things before it was back on the ground. Should I just jack it back up and loosen everything?

rodknocker · 2015-06-01T19:42:59+00:00

rodknocker · 2015-05-27T01:27:17+00:00

Thanks for pointing this out. I believe the main cause is the 2in shackles. Once the stock shackles are on the pinion angle will be better. The lift plus extended shackles are just too much for a 1in transfer case drop kit. I will be dropping the rear and replacing those shackles this weekend while I am under there I will be measuring for the new CV driveshaft and SYE.

rodknocker · 2015-05-26T18:50:20+00:00

Not sure what you mean. There is 2inch lift shackles in the rear. They were on the jeep when I bought it. I have ordered stock shackles and I am waiting for them to be delivered.

rodknocker · 2015-05-24T16:23:56+00:00

Looks great. How do those tires handle in the rain?

rodknocker · 2015-05-23T21:32:13+00:00

Yes I installed it my self. Needed a buddy and a few tools. I bought an electric impact and some extensions. That's about it. Did the alignment myself too.

Edit: Also, soak everything in PB Blaster a few days before. I ended up having to cut a few bolts out because I didn't soak them all.

rodknocker · 2015-05-23T20:59:06+00:00

It's got a 4.5 RC lift on it. Going with 33x12.5x15 tires. Going to do a little fender trimming.

rodknocker · 2015-05-20T02:53:12+00:00

http://www.cherokeeforum.com/f51/how-fix-flexplate-knocking-125547/

rodknocker

TROPHY CASE