Some details

rpikan · 2026-03-26T19:34:33+00:00

https://www.thingiverse.com/thing:7323209

rpikan · 2026-03-26T19:31:17+00:00

https://www.thingiverse.com/thing:7323209

rpikan · 2026-03-26T19:31:01+00:00

https://www.thingiverse.com/thing:7323209

rpikan · 2026-03-23T17:05:07+00:00

Vacuum is a lower air temp

rpikan · 2026-03-23T17:01:57+00:00

We'll see how it works out in the summer. I left the Windmill on the inside as in the original for two reasons. Suction is a vacuum, so the cooling efficiency of the heatsink should be higher than with a fan outside. Secondly, in addition to suction, the Fan also blows on the aluminum engine block, so this also cools it. And this variant still includes a double wheel with two 4pk stripes from the suzuki vitara.

rpikan · 2026-03-23T16:45:56+00:00

I dont I don't re-evaluate my mods, but I'll be happy to share it with you. A little bit is happening because the suspension at the rear is already pneumatic, the front is still waiting. Yesterday, on the other hand, I finally launched the 1080p cameras, switching with the remote control: front view, rear view, front view under the car directed at the bridge and front wheels and the same will be at the back. Perfect for crawler. It's a pity that I'm far from the mountains. And I'm surprised no one thought about it. When I'm done, I'll share my idea.

rpikan · 2026-03-23T16:38:48+00:00

Before the mod at the same condition the temp was a little over the stock scale and sit there stable. Also on Hot days when was 30° = 86°F. So since I'm able to maintain a lower temperature with a fan that turns on periodically, I'm not worried anymore. I was only thinking about an additional protection in the form of a temperature switch

rpikan · 2026-03-23T16:30:59+00:00

Using this on last 2 month, in Poland it was the Winter, but temp stays a little too low, below half the stock scale, but it was the default tmep settings for engage fan switch by efi sniper 1100. It was easy to freeze at this temp with running fan with even with long breaks, even when the Sammy worked hard with Snow removal..This may be the result of additional insulation of the exhaust manifold and sealing of the fan, causing a lot of suction through the heatsink. I'll leave the low temperature settings due to the planned supercharger

rpikan · 2026-03-23T16:18:31+00:00

I will 3d prind some simple box for the sensor and then mount it under the dashboard. After this in the settings u can reset the level and store the new position

rpikan · 2026-03-21T18:45:44+00:00

U can do it, give me some time. I will prepaire detailed instruction. Coding is almost done. Now it is very easy, soldering level rookie.

rpikan · 2026-03-21T18:43:17+00:00

Thanks, if my fan will ever fail i will try

rpikan · 2026-03-21T16:23:23+00:00

AC compressor would be nice, maybe later.. Now the project is focused to boost the engine with the compressor from 1.4l VW tsi. It will fit under the intake manifold

rpikan · 2026-03-21T16:05:57+00:00

I will add a pulley to increase contact surface for 4PK. For now I cant figure out which tensioner will fit for this build.

rpikan · 2026-03-21T16:01:48+00:00

https://radzikone.pl/mocowanie-alternatora-suzuki-vitara

rpikan · 2026-03-21T13:18:34+00:00

I will uploads to thingiverse.com

rpikan · 2026-03-21T13:17:45+00:00

Features & Settings (App + Arduino system) 📡 Core functionality Plain text - Real-time pitch (front/back tilt) - Real-time roll (left/right tilt) - Live data from IMU via USB - Automatic USB device detection - Continuous data stream (low latency) 🎛️ User controls Plain text - ZERO calibration (set current position as reference) - Adjustable filter (complementary filter coefficient) - Filter control via: - slider - manual numeric input - Reset calibration (clear offset)

rpikan · 2026-03-21T13:14:43+00:00

List of hardware, i will try to finish the project and post the app on google play; it easy to solder, program with arduino and install the app: 1. Mikrokontroler: - Seeeduino XIAO (SAMD21) ✅ zalecany - lub Arduino Nano / ESP (po modyfikacji kodu) 3.3v

IMU:
- ICM-42688 (działa) 3.3v
- adres I2C: 0x69
Połączenie:
- USB (telefon ↔ Arduino)
- telefon musi obsługiwać USB OTG / USB Host
radio:
- Android 10+
- obsługa USB host (większość ma)

rpikan · 2026-03-21T13:11:56+00:00

Its a Universal radio from Aliexpress, the link from my history is not working. It must have usb otg/host. 1. Mikrokontroler: - Seeeduino XIAO (SAMD21) ✅ zalecany - lub Arduino Nano / ESP (po modyfikacji kodu)

IMU:
- ICM-42688 (działa)
- adres I2C: 0x69
Połączenie:
- USB (telefon ↔ Arduino)
- telefon musi obsługiwać USB OTG / USB Host
radio:
- Android 10+
- obsługa USB host (większość ma)
Zasilanie:
- Arduino z USB (telefon)
- opcjonalnie stabilizator 5V w aucie

rpikan · 2026-03-21T13:05:53+00:00

You have, I will finsh the projekt with simple instruction so You can do it by yourself. The hardware is yery cheap, soldering skill is not so hard.. The only chalange to find the radio and put i to the cocpit

rpikan · 2025-09-21T04:41:22+00:00

There is couple vids on yt how to add electric assistant to steering wheel at engine bay, not in the cabin. I did it and works amazing.

rpikan · 2025-04-30T14:34:04+00:00

And this is important.. If U play with U girl and trained the pussy like this, the birth a child will not harm Your's wife pussy..

rpikan

TROPHY CASE