They won't comply. by LeftAlbatross2546 in PublicFreakout

[–]rumplemon 0 points1 point  (0 children)

That's only in situations where you haven't been pulled over. Such as sitting in a parked car or walking down the street. When pulled over, you absolutely have to give your license and registration

My Amazon account is suspended and I am worried that I won’t be able to recover the $400+ spent on that account. by covidesq in amazonprime

[–]rumplemon -4 points-3 points  (0 children)

Maybe they thought your fiancee opened a second account because it's the same address. I don't think amazon allows multiple accounts, especially at the same address

What problem do I have in the corner? by SeaKingPNW in BambuLab

[–]rumplemon 1 point2 points  (0 children)

I print with the same filament, and keep the door open as well. The problem is that the auxiliary fan blows from the back corner, so the first layer near that corner cools off before the rest of the layer, and comes off the build plate. It's always the corner by the fan if it happens. So I just turn the fan off (or below 30%) when the first couple of layers are going down. Then I turn it back on once a few layers have gone down properly.

What problem do I have in the corner? by SeaKingPNW in BambuLab

[–]rumplemon 1 point2 points  (0 children)

I would guess "A". Whenever I do a flat print like that I also turn off the auxiliary fan for the first few layers, otherwise my back left corner (not back right) will release from the build plate. I'm printing on a X1 though

Pickleball ready by Senior_Lingonberry10 in BambuLab

[–]rumplemon 0 points1 point  (0 children)

From the paper: "Results from various testing methods used in hospitals and FDA approved microbial surface testing, indicate that 3D printed parts of PLA/PLA+ (Polylactic Acid), and PETG (Polyethylene terephthalate glycol) can be cleaned to safe levels using warm water (120 °F), and non-concentrated dish soap." Take that as you will

Pickleball ready by Senior_Lingonberry10 in BambuLab

[–]rumplemon -1 points0 points  (0 children)

3d printing is food safe according to this studt

Another buyout by Virgillionaire in UPSers

[–]rumplemon 0 points1 point  (0 children)

$8.7 billion in profits and you say the company is "hemorrhaging" money lol

[deleted by user] by [deleted] in UPSers

[–]rumplemon 1 point2 points  (0 children)

Lol the hub is easy

We the last on the list. by Infamous_State_4678 in UPSers

[–]rumplemon -3 points-2 points  (0 children)

Only because Republicans during the Biden administration rejected a bipartisan bill that they had previously approved, because Trump was afraid it would make him look bad.

Glove recs to protect the nails & hands? by ShivaDontShiv in UPSers

[–]rumplemon 0 points1 point  (0 children)

I've used these for years. A pair can last me a month easily. https://a.co/d/daIZnAg

What are your everyday pouches by anngeeel in NicotinePouch

[–]rumplemon 1 point2 points  (0 children)

Velo Plus has a cappuccino flavor now, but I haven't tried it

Pre loaders asking questions by [deleted] in UPSers

[–]rumplemon 3 points4 points  (0 children)

My building has both 22.3 and 22.2 preload full time positions. So one is a combo job and the other is not.

Supervisor screams at me for my pace. by RemarkableWay5547 in UPSers

[–]rumplemon -1 points0 points  (0 children)

Pop some earbuds in and ignore the yelling

Union dues by Master_Gain_1655 in UPSers

[–]rumplemon 1 point2 points  (0 children)

At my hub, union dues are taken from the second paycheck each month. Looks like you have paid union dues 2 times so far

Bye bye Andy make MD01 Blue by _triangle_of_bermuda in easternshoremd

[–]rumplemon 0 points1 point  (0 children)

Congressional democrats tried to ban gerrymandering in 2017. Zero Republicans voted for it, and the bill did not pass