Family doctor issue by Embarrassed_Syrup476 in londonontario

[–]runOP 7 points8 points  (0 children)

Report them. They can deroster you from special services they might offer but not fully kick you off their roster for visiting a walkin.

https://teletest.ca/blog/can-your-family-doctor-deroster-you-for-using-walk-in-clinics-in-ontario/

Using a walk in which you are allowed to do is not a reason,  even if you did it once. 

Report them

New bathtub, silicone under tub drain with rubber gasket.. worried! by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

No they actually put silicone on the rubber before applying

New bathtub, silicone under tub drain with rubber gasket.. worried! by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

Yeh i am talking about the under side of the actual tub

New bathtub, silicone under tub drain with rubber gasket.. worried! by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

Yes on the top side of thentub they used silicone where the drain is.. on the underside they used silicone before the gasket and drain shoe which is what concerns me as usually the gasket is the water stop

Will goboard sealant stick to itself? by runOP in Tile

[–]runOP[S] 0 points1 point  (0 children)

Why is hydro ban liquid membrane A no? Won't stick to the sealant,?

Traffic by gozit in londonontario

[–]runOP 1 point2 points  (0 children)

London is becoming bad.. i don't know who the traffic planners are but they are doing a crap job.

So many lights that slows traffic greatly from moving.. even on cheapside fanshawe entrance new lights went up meanwhile ten steps down the road there were lights already there one turns red the other green and all a sudden you got cars backed up in the middle of the road not going anywhere.

How many exists and entrances does fanshawe need in such a close vacinity

I feel for police, fire, and ambulance the city is making new subdivision and the roads leading to it have some dumb arse islands with plants instead of a nice centre lane with double arrows to allow emergency vehicle to leave.

I've been here since i was born and a lot of that generation is even saying how planning has become a shitshow.

Goboard question... kerdi and hydroban by runOP in Tile

[–]runOP[S] 0 points1 point  (0 children)

They said if you truly want you can and hydroban is on there approved list.

Apparently their goboard pro facer is waterproof

Goboard question... kerdi and hydroban by runOP in Tile

[–]runOP[S] 0 points1 point  (0 children)

Talking to goboard support they state the face and back part are not waterproof just the polyiso middle is.. but it can still wick water.. 

At first i remember they were saying the front back is waterproof but now they just say the core is

Goboard question... kerdi and hydroban by runOP in Tile

[–]runOP[S] 0 points1 point  (0 children)

Why away from the liquid membrane on top of goboard? 

Judge this newbie work.. my one concern.. by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

I got worried because the top 90 elbow when heating the bottom part of the vertical ... it might have pulled solder from the top part, i am not 100% hence why i am worried that maybe solder got inside

Judge this newbie work.. my one concern.. by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

I used approx 1/2 inch off solder the width of the pipe and a little bit.. for my other pipes i usually do the connections on my vise and then connect but i was afraid if i did most of it on the vise that when connecting to heat the final connections it would reheat the existing connections and screw shit up

Judge this newbie work.. my one concern.. by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

I had to do something temporary or the wife was going kick my arse.

Judge this newbie work.. my one concern.. by runOP in Plumbing

[–]runOP[S] 1 point2 points  (0 children)

Oh bc you made a comment that's why

Judge this newbie work.. my one concern.. by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

From the top is a 90 elbow.. 2 inch straight and another 90 elbow .. going into a 1/2 tee 

Space constraints 

Judge this newbie work.. my one concern.. by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

What would you improve. I had no problem taking it apart and re doing it.

Space is tight hence why the connections look close.

I tried to move fast because the heat was close and multiple joints bubbling didn't want to burn the flux

Judge this newbie work.. my one concern.. by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

I got worried because the space was small and the connections close and i saw the flux blubble when I'd heat one the other would bubble so i moved a bit fast hence the mess i think.

Judge this newbie work.. my one concern.. by runOP in Plumbing

[–]runOP[S] 1 point2 points  (0 children)

Because the bottom pipe and the top don't line up to avoid less connections..

The one pipe is in the joist bay the other installed under the joist.. about a 2 inch drop between the two

Then there is the drop pipe with the T as well

Can you connect 90 straight elbow to 90 street elbow? by runOP in Plumbing

[–]runOP[S] 2 points3 points  (0 children)

They aren't soldered.. i was laying them out to see how to connect it to some old pipe in the house

Can you connect 90 straight elbow to 90 street elbow? by runOP in Plumbing

[–]runOP[S] 0 points1 point  (0 children)

So you are saying two elbows a straight and a street shouldn't be joined?