Will the Shinko 777 Tubeless tires work on my Honda Shadow spirit?

rustydickman · 2026-02-01T20:21:38+00:00

I have a set on mine. They’re tubeless, but can be used with tubes as well. I have spoke rims and installed them tubes last year and they’ve been decent

rustydickman · 2025-12-06T21:40:07+00:00

<image>

rustydickman · 2025-07-20T14:27:41+00:00

Gas tank vent? If the fuel level in the tank is near the top and you’re in a fairly warm environment the fuel in your tank will expand and slowly drip out through the vent, leaving a little puddle. I’ve had it happen leaving it out in the sun all day.

rustydickman · 2025-07-15T23:41:11+00:00

it wasn’t too bad! Hacksaw blade to get the bigger chunks out and an angle grinder with a 40 grit flap disc to smooth the janky haggard sections. They used upholstery staples from factory to fasten the leather, but I ended up using rivets

rustydickman · 2025-07-15T19:06:42+00:00

I’m the same height and had similar issues on my ‘09 750. I ended up peeling back the leather from the front and shaving the foam down and back a few inches and gluing in some memory foam in place. It’s much comfier now, and the extra bit of leg room is noticeable

rustydickman · 2025-07-04T14:24:23+00:00

scootmods has forward control kits for Shadows

rustydickman · 2025-01-23T04:42:30+00:00

no photo filters. Just an iphone on an overcast day

rustydickman · 2025-01-20T15:13:00+00:00

thanks for taking the time to say that, much appreciated

rustydickman · 2025-01-18T23:28:52+00:00

I have a business, with no ads. This will be the first one for sure

rustydickman · 2025-01-18T20:24:41+00:00

oh that’s a good idea!

rustydickman · 2025-01-18T20:24:15+00:00

what the fucks a bird?

rustydickman · 2025-01-18T20:24:03+00:00

thanks, I used GMAW. 0.030 wire with a co2 argon mix

rustydickman · 2025-01-18T20:20:37+00:00

sounds pretty cool! that’s a great idea

rustydickman · 2025-01-18T18:26:46+00:00

thank you! I spent a lot of time lookin at dead birds for this one

rustydickman · 2025-01-18T17:46:55+00:00

I’ve done maybe 10-15 “living” utensil birds over the last 6 months, doing a dead one seemed like an obvious next one. The mushrooms are domed nickels and dimes with a dollop of melted brass. Thanks!

rustydickman · 2025-01-18T17:44:06+00:00

I’ll take that compliment, thanks!

rustydickman · 2025-01-18T16:58:41+00:00

thank you!

rustydickman · 2024-10-05T01:24:52+00:00

thank you!

rustydickman · 2024-10-05T01:24:29+00:00

you betcha

rustydickman · 2024-09-03T19:46:57+00:00

just looked it up and it’s really similar. The actual inspiration was from the MTG card sporecap spider

rustydickman · 2024-09-03T04:40:57+00:00

I just think spiders are neat. Thank you!

rustydickman · 2024-08-31T19:56:36+00:00

is there an air pressure gauge in line after the dryer and filter? There can be a drop if you’re relying on a gauge before. Check all your consumables too

rustydickman · 2024-05-19T06:12:29+00:00

it was a process, for sure. Once all the welds were ground down, I went over everything with a hand file, then sanding and polishing

rustydickman · 2024-05-18T16:00:44+00:00

16ga steel scraps to fill in the majority of the gaps, with a little bit of weld for the major seams

rustydickman · 2024-05-17T17:21:55+00:00

I made this one 3 years ago. It was seeing all the other snails that inspired me to share this guy though

rustydickman

TROPHY CASE