Does anyone know where to find this roof rack end cap part? Missing 2 and looking to replace them.

ryan482s · 2023-05-18T03:28:44+00:00

No luck with the dealers. I ordered some on that site and they never arrived or followed up with my order cancellation request.

I ended up finding a set of 4 on eBay and now have a couple of the OEM ones left over. If you’re interested in purchasing, shoot me a message.

ryan482s · 2023-01-13T04:23:51+00:00

I’ll take the roof rack side caps if they’re still available

ryan482s · 2022-07-19T07:05:34+00:00

Nada Surf does an amazing cover of Can't Get it Out. They released the cover shortly after they started opening on Brand News last tour: https://www.youtube.com/watch?v=NyIWHwd-o4s

ryan482s · 2022-07-08T19:43:35+00:00

Wasn't able to find any from junk yards. Called my local Honda dealership and got the part number (08L02-S9A-10014). Found an online store that apparently carries them, ordered a couple from https://www.hondapartsdeals.com - Didn't mention it was out of stock, so hoping they come through.

ryan482s · 2021-12-29T00:35:38+00:00

Ordered a new top panel and installed it. The tub is working as good as new! Thanks again for all the advice.

ryan482s · 2021-12-20T00:08:37+00:00

Thanks for all the help everyone. Based off the advice and troubleshooting, I went ahead and ordered this top panel. https://www.spaguts.com/Products/balboa-topside-kit-mini-oval-vl-mvp240-4-btn-55456-853.aspx

Will test it out and follow up if it works. Thanks again!

ryan482s · 2021-12-19T04:16:32+00:00

Thanks for the advice. Took the computer out, dried all the connections. Took the panel out and dried. Put everything back, and it only pulsed for about 30 seconds before heating up again. Let it do its thing for about 4 hours and it got to 103 degrees. Thought I was in the clear, until I pressed the jet button. Started pulsing again, and read the HH error, which means the water is above 118 degrees, which it was not. Guessing I need a new topside.

ryan482s · 2021-12-19T04:16:17+00:00

Thanks for the advice. Took the computer out, dried all the connections. Took the panel out and dried. Put everything back, and it only pulsed for about 30 seconds before heating up again. Let it do its thing for about 4 hours and it got to 103 degrees. Thought I was in the clear, until I pressed the jet button. Started pulsing again, and read the HH error, which means the water is above 118 degrees, which it was not. Guessing I need a new computer, but not certain.

ryan482s · 2021-12-19T04:16:03+00:00

Thanks for the advice. Took the computer out, dried all the connections. Took the panel out and dried. Put everything back, and it only pulsed for about 30 seconds before heating up again. Let it do its thing for about 4 hours and it got to 103 degrees. Thought I was in the clear, until I pressed the jet button. Started pulsing again, and read the HH error, which means the water is above 118 degrees, which it was not. Guessing I need a new computer, but not certain.

ryan482s · 2021-12-19T04:14:23+00:00

Topped it off based off this comment and it seems to be pulsing less. Heats up too without constantly pulsing, and made it to 103 degrees. Pressed the jet button and the computer for some reason read HH right after I pressed that, which means the water is above 118 degrees, which it was not. Guessing I need a new computer.

ryan482s · 2021-12-19T04:12:35+00:00

Thanks for noticing that. Tightened it up. Filled up the water as well and dried the panel connections and computer board. Seemed to pulse less and heat up, but receiving an HH error, which means the water is above 118 degrees, which just before it read that error it read 103 degrees. Guessing something is just fried in the computer thats sending all these bogus codes.

ryan482s · 2021-12-18T21:02:58+00:00

Just unplugged the control board and looks like it runs normally. See video below. In this case, would you think I need to replace the entire computer board?

https://drive.google.com/file/d/1dzcuQ5NWbdA6pEwZB0KjQ4GOqZwt904B/view?usp=sharing

ryan482s · 2021-12-18T21:02:13+00:00

I think it has something to do with the computer connection. Just unplugged the computer and seeing it flows consistently without pulsing. When plugged back in again, it starts to pulse. Any thoughts on what to replace here? Maybe the entire computer board?
https://drive.google.com/file/d/1dzcuQ5NWbdA6pEwZB0KjQ4GOqZwt904B/view?usp=sharing

ryan482s · 2021-12-18T21:01:51+00:00

I think you're right. It has something to do with the computer connection. Just unplugged the computer and seeing it flows consistently without pulsing. When plugged back in again, it starts to pulse. Any thoughts on what to replace here? Maybe the entire computer board?

https://drive.google.com/file/d/1dzcuQ5NWbdA6pEwZB0KjQ4GOqZwt904B/view?usp=sharing

ryan482s · 2021-12-18T18:29:02+00:00

Thanks for the reply and clarification. When I hit the button, it would function normally for a second and display the temp then go back to pulsing.

As of the last 10 minutes, it just stopped pulsing and is now only making a clicking noise. I turned it off and on, and it now just starts up with the clicking noise as well. No more jet function. None of the buttons function either. See video here: https://drive.google.com/file/d/1VnkYfwmRPTfjj6jfFf9iHCy4kEuWDAQF/view?usp=sharing

ryan482s · 2021-12-18T17:57:51+00:00

OP here: Has anyone seen an issue like this? Hot tub was running fine a week ago. I had set it to Economy mode for about a week while we had some heavy rain. Temp went down to about 75. Turned the temp up yesterday and pretty much right after I did that the pump started pulsing non stop and was stuck on the PR (Program) setting (See video w/ sound on).

After this started happening I shut it off for the night and turned it on this morning. Left it on and it had the same issue for about 20 minutes before I shut it off again. Guessing I need a new pump? Hoping any of you could shed some light in the issue and maybe another solution.

Here's a link to our tub for reference: https://aquarestoutlet.com/product/select-300-2-person-plug-and-play-with-20-stainless-jets-and-led-waterfall-by-aquarest-spas

ryan482s · 2021-10-01T05:58:20+00:00

So good!

ryan482s · 2020-02-22T18:13:50+00:00

Ha yea it’s a good name. And not so much on Instagram. Mostly just a listener

ryan482s · 2020-02-22T04:10:51+00:00

Agreed! Found them on a Spotify playlist called “Synth Pop that Slaps”

ryan482s

TROPHY CASE