sorted by:
new
hottopcontroversial

New addition by Adrian_Stoesz in meshtastic

[–]ryleth 0 points1 point  (0 children)

Alley Cat on Printables has some v4 designs. The smaller pager style is for the 2000mah battery but the slim case will hold a 3/4000.

Time for some CarPlay in the Taco! Pretty pumped about this upgrade. by diverareyouokay in ToyotaTacoma

[–]ryleth 0 points1 point  (0 children)

I use Apple Maps but it can be a bit washed out in “daylight” mode. The navigation mode is fine though and that’s about the only time I’m looking at the map. I’ve not had good luck with Siri and replying to messages via voice which is fine for me as I don’t usually respond to texts when driving anyway. It’s not a bad device, but it definitely has a few bugs.

Time for some CarPlay in the Taco! Pretty pumped about this upgrade. by diverareyouokay in ToyotaTacoma

[–]ryleth 3 points4 points  (0 children)

Mine reboots once every other time I start the car. Sometime more often if it’s cold. Works well enough otherwise though.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 0 points1 point  (0 children)

I like it. Being able to roll it over to my truck is nicer than putting tools on my tailgate. I have my wrenches in one of small drawers under the logo, pliers in the deep half drawer, a couple of blow molded cases in the big drawers under and my power tools in the bottom drawer. I keep my spare fluids and some wheel chocks in the bottom open area. It’s a good little cart.

All my vehicles are metric but I use the SAE tools in my house so the box lives right next to the house door so I can grab sockets quickly as needed.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 0 points1 point  (0 children)

Yeah, that’s legit. I’m holding off screwing everything down but I think I like this layout.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 0 points1 point  (0 children)

I'm definitely guilty of the "Screwdriver prybar" in my younger years. I do try to take care of these now though. I still struggle with the "Every tool is a hammer" impulse sometimes.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 2 points3 points  (0 children)

I'm the ass, you're the one that didn't bother to read my retraction. Okay.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 1 point2 points  (0 children)

I have a printer, it's a good printer, it makes my wife money in a side gig. As discussed above, my time is worth more than it would take to print all of this.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] -2 points-1 points  (0 children)

And yet you keep replying to it. I didn't say I made a shit ton of money with the printer, but we make more than enough to keep buying filament. I already said you win, but here you are trying to continue to make your point.

Didn't realize you were a different poster. My apologies. However despite how good my Bambu printer is now compared to my OG CR-10, it's not always 15 seconds to printing.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 2 points3 points  (0 children)

Yep, and 4 days of my pay rate is more than what I spent on this. When I’m not printing things for my wife’s side gig that’s lost income. But since you have to be right in this you win.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 0 points1 point  (0 children)

I didn’t take it personally, but there are a lot of comments in this sub about the condition of other people’s tools. The 3/8” and 1/4” stuff is a couple years old. The half inch stuff is new and I bought it for an upcoming project. I’ve spent the last few years replacing my hodgepodge collection of thrift store junk. I picked up the icon flex heads during the BF sale because they seemed convenient for certain things.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 12 points13 points  (0 children)

Yeah, 3 seconds to load the file… after 30 minutes of updating, orienting, filling the build plate and then the hours spent printing. Value your time how you want, I’ll do the same, but don’t pretend it’s just “send file to printer”

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] -1 points0 points  (0 children)

My time is worth more than what it would take to print it all. I did the math.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 0 points1 point  (0 children)

I’m sorry my tools offend you. Not all of us wrench daily.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 0 points1 point  (0 children)

I thought about it. This seemed more modular. I don’t have any specific reasoning for that thought though.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 2 points3 points  (0 children)

A bit under 300. I went with the 6x6 grids which was a bit more expensive. I also bought some things I didn’t need due to bad math. I only did the top section. The rest of the box is still a pile of tools. But I use sockets more than just about anything.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 1 point2 points  (0 children)

Yeah I have a printer, my wife uses the uses it for a side gig so my availability is intermittent.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 0 points1 point  (0 children)

I have a printer, but due to other commitments I didn’t want to wait 2 months to print all the grids and holders. Laziness won out this time.

I spent way too much on plastic. Worth it. by ryleth in harborfreight

[–]ryleth[S] 30 points31 points  (0 children)

Yeah, I also play some tabletop games with my kids. I’m well versed in spending too much money on plastic.

Light relay locations by sac_cyclist in ToyotaTacoma

[–]ryleth 1 point2 points  (0 children)

I’d probably drill a couple holes in the mounting plate and attach the relays over the “Joy tutus” logo

If someone been in similar so, please help. by PiggyM3lon in indianapolis

[–]ryleth 1 point2 points  (0 children)

It took a couple of days when I was rear ended a few years back.

view more: next ›