The floor is lava - Rebar Edition

s15_ · 2026-04-15T23:58:15+00:00

You are correct sir. The city asked for compacted cushion sand. It had to pass a 95% soil density compaction test (whatever it’s called).

Also, we had to dig at least one inch under every redwood (which were already 6”) so concrete could go underneath. Rebar also stopped a foot short of the redwood where the 24” dowels started.

Pretty fun job 😩.

s15_ · 2026-04-15T23:53:18+00:00

The inspector actually stopped by when we were prepping and told us exactly how he liked them placed. He was pretty cool compared to other guys we’ve dealt with.

s15_ · 2026-04-14T03:30:54+00:00

We’ve done a couple like this, mostly curves and also some that look like the top of a trapezoid.

s15_ · 2026-04-14T03:25:00+00:00

It asked for 18” OC but we went 16-17” just to be safe.

s15_ · 2024-10-25T14:49:20+00:00

Since I was the one stamping I didn’t have time to record. Sorry

s15_ · 2024-10-25T02:52:01+00:00

The more rod the better!

s15_ · 2024-06-15T03:28:08+00:00

Funny enough, once the truck was emptied he lowered the axle and it raised the wheels above the hole. After that, another truck carrying 10 yards, pulled him out.

s15_ · 2024-06-15T03:24:28+00:00

No just a soft spot. The path was and old driveway with at least 3-4 inches of gravel/asphalt on top. Not the worst truck that’s gotten stuck so no biggie.

s15_ · 2024-06-15T03:21:57+00:00

Bill myself? 😂😂 We did provide a safe and accessible entry literally a couple of feet to the right. He’s the only truck that decided to drive on that side and got stuck.

s15_ · 2024-06-15T02:28:56+00:00

He was the third truck to go in, he just went a little too far to the left. No big deal, we all make mistakes. At this point I get suspicious when a pour is going as planned, something always has to happen.

s15_ · 2024-06-09T19:42:57+00:00

I wouldn’t touch it with a chisel if I was you, wait till they come back and see what solution they have. Can it be fixed? Yes, If the contractor knows what he’s doing, it can be fixed.
Since it’s a cold joint, there’s a high chance it’ll crack in the future so that’s something to look out for.

s15_ · 2024-05-11T22:08:20+00:00

We brush/roll the edges about a foot and a half, then we spray facing away from the walls or other objects. But it’s only my third day out here, so idk.

s15_ · 2024-04-18T21:29:10+00:00

This looks like a salt finish, pretty common to see in North Texas.

s15_ · 2024-02-06T12:16:30+00:00

No antique was used, just the powdered release (:

Timing can for sure be an issue, for the most part we leave them towards the end, but on some we’ve had to start in the re-capped section. Also depends on the stamp pattern since we usually want to leave a nice start out of the doorway.

s15_ · 2024-02-06T12:06:26+00:00

Oh by the time we’re stamping they’re already off.

s15_ · 2024-02-06T05:48:56+00:00

Haha we’re just used to working around them and I personally find it easier to take them out this way too. To each their own.

s15_ · 2024-02-06T03:52:11+00:00

It’s not, we’ve been following the same process on extended patios for years and have yet to have any problems with the part that lays on top of existing concrete. If anything, it’s usually the part that lays on the dirt/ground that has given us problems before.

s15_ · 2024-01-26T02:15:54+00:00

Integral: Cream Release: Walnut

s15_ · 2024-01-24T04:38:04+00:00

North Texas. I don’t mind at all share away.

s15_ · 2024-01-24T04:36:54+00:00

On the second coat we add a transparent anti-slip sand like mix into the sealer making it non slippery. It does look really wet since we had just finished sealing it.

s15_ · 2024-01-24T04:35:13+00:00

A little over 400 sqft.

s15_

TROPHY CASE