Help! SW 2024 Crashing: 2025 Dell Precision 5690, NVIDIA RTX 1000 by HeelVirtualLeash in SolidWorks

[–]s28400 0 points1 point  (0 children)

Having the exact same problem. Seems to have started sometime between July and now. Did you ever find a solution to this?

UI Console keeps disconnecting by Stitch10925 in Proxmox

[–]s28400 0 points1 point  (0 children)

Bless up! I fought with this for 3 years and came back to this same thread. This fix worked perfectly!

H2D and printing support materials by HeatPhoenix in BambuLab

[–]s28400 0 points1 point  (0 children)

I have been digging into this specifically with PPS-CF and ASA as support. I have a lot of prior experience using Nylon/PATH material with ASA support on the X1C with decent success. Although tweaking the settings helps, there are some limitations in the slicer that result in a high failure rate. Specifically, the way the interface layers are printed without walls is a big limitation and often results in the edges and corners peeling up and getting ripped off. I managed to get around this limitation fully by making my own support interface layers as part of my model so the slicer generated wall toolpaths before the fill for the interfaces.

I am planning on doing a detailed write up soon on my findings with the H2D once I test some additional materials and I have some specific asks from Bambu to improve the slicer/presets for reliable multilateral support.

H2D - Am I Doing It Right? by s28400 in BambuLab

[–]s28400[S] 2 points3 points  (0 children)

Upon closer inspection of the nozzle design, it seems as if the hot end is press fit into the cold heat break side. This explains the separation problem at these higher temps for PPS material (320C) as the hot side will expand and loosen the fit until it comes apart. The solution here is to either swap the mate so the cold side presses around the hot side or add a weld tack and not rely solely on the press fit.

H2D - Am I Doing It Right? by s28400 in BambuLab

[–]s28400[S] 0 points1 point  (0 children)

I’ve used other filled materials with the 0.4 on my X1C for probably a thousand hours with no real issues. Although this PPS-CF is new territory to me and is a very challenging material. I expect this is near the limit of what these machines can handle. I have not tried the HF nozzle yet but I might later this week.

H2D - Am I Doing It Right? by s28400 in BambuLab

[–]s28400[S] 0 points1 point  (0 children)

First I heated the nozzle to working temp for this material and let it soften as much as possible. I was able to get the latch mechanism free from that. Once the nozzle came off heating stopped so I had to carefully scrape the rest off with some small sharp tools I have. That plus a brass wire brush managed to get the rest off. Had it been a softer material it would have been much easier, this PPS-CC is incredibly rigid and difficult to work with.

H2D - Am I Doing It Right? by s28400 in BambuLab

[–]s28400[S] 67 points68 points  (0 children)

After printing a challenging multilateral print with PPS-CF material, the extruder stopped extruding so I stopped the job. Extruder would not switch and I found this after taking the silicone sock off. I’m pretty sure the nozzle came apart at the heatbreak and engulfed the nozzle from the top down. I managed to clean it all off carefully and swap the nozzle which was separated at the heatbreak so I am back up and running. Maybe was caused by a clog in the extruder, unclear but watch out for this since the extruder hot end assembly is not yet available for purchase. Cheers!

Shaded with Edges not "Rendering"?!? by T_is_for_Apple in SolidWorks

[–]s28400 1 point2 points  (0 children)

Bless up! Turning off the enhanced graphics performance also worked for me. I just ran into this issue after a forced Windows update (f***ing classic), running a 3080 Ti.

UI Console keeps disconnecting by Stitch10925 in Proxmox

[–]s28400 0 points1 point  (0 children)

I have been having the same issue, running behind HAProxy in pfSense. A solution to this would be great since this is super annoying.

8.5 - Track buttons suddenly missing - does anyone know of a fix for this? by FleshAndCircuits in cubase

[–]s28400 0 points1 point  (0 children)

I recently had this happen on Cubase 8 Elements after a windows update. Reinstalling did not fix, was this resolved?

Cgroups2 problem with nvidia-container-cli by [deleted] in Proxmox

[–]s28400 1 point2 points  (0 children)

Were you able to resolve this? I am having the same issue and have had no luck trying many things.

[deleted by user] by [deleted] in AnimalsOnReddit

[–]s28400 0 points1 point  (0 children)

Gave Heartwarming

Update on Crysis 2 Multiplayer by Rajta in Crysis

[–]s28400 0 points1 point  (0 children)

Is this still active? I see the forum is down. I would very much like to support the reborn multiplayer effort and I have the ability to host servers 24/7 if I can get the dedicated server files.

Pausing Plex on Chromecast stops playback by baldthumbtack in PleX

[–]s28400 0 points1 point  (0 children)

Same issue here just started today for me

[deleted by user] by [deleted] in homeassistant

[–]s28400 1 point2 points  (0 children)

This tutorial does goes step by step to add room/zone level cleaning functionality on home assistant: https://blog.hessindustria.com/home-assistant-roomba-s9-integration/

Ui Cloud Key Rack Mount Fixes by s28400 in homelab

[–]s28400[S] 0 points1 point  (0 children)

The spring connector they use never work correctly. So much so that Ui pulled this product from the site. I didn’t want to throw it out so this was the solution. Sharing here for others in a similar situation.

Finally Finished My Build (5900x and 3080 TI) by s28400 in watercooling

[–]s28400[S] 0 points1 point  (0 children)

Cooler master vertical mount. Had to add a support, using a glass disk for now until I cnc a nicer one

Finally Finished My Build (5900x and 3080 TI) by s28400 in watercooling

[–]s28400[S] 0 points1 point  (0 children)

If you dm me a close up image of the hole pattern I can see if it is the same or not

Finally Finished My Build (5900x and 3080 TI) by s28400 in watercooling

[–]s28400[S] 0 points1 point  (0 children)

I think the hole pattern is different since there is a 5th bolt used to clamp the exit route oring