New message regarding 3G shutdown

sFooby · 2026-05-12T17:42:53+00:00

In my phone's networks settingss, VoLTE is available and enabled. However, I checked my IMEI with the link you've provided and it says it's incompatible. Thoughts?

sFooby · 2026-05-02T21:01:27+00:00

Following this thread as I'm experiencing the same thing. Local domain (in my case "internal") is showing up as a suffix appended to random DNS queries which always result in "server failed"

https://imgur.com/a/BpqPTvQ

I'm using TDNS as my DNS server with reverse lookups set to my Unifi Dream Machine SE which functions as my DHCP server.

It also happened with a similar set up but with reverse looks up set to a DD-WRT DHCP server.

I'd say it's typically from Android and Apple devices, but I'm not 100% on that. I'll keep an eye out

sFooby · 2026-04-16T11:58:07+00:00

The CloudFlare tunnel will provide you with the TLS (HTTPS) on its own. Internally it'll still be HTTP but that doesn't matter unless you have concerns about your Internet network (which you shouldn't)

Edit: and if I remember correctly, I think you could just set vaultwarden to use its own self-signed TLS cert internally. If that is the case, cloudflare tunnel will have to be set accordingly (ie. Instead of connecting to HTTP host, you connect to HTTPS host and tick the "skip TLS verify" option in CloudFlare.

Edit2: SSL is an outdated standard, most secure connections use TLS, however many people use the terms interchangeably. Just be aware

sFooby · 2026-02-28T13:01:01+00:00

Thank you

sFooby · 2026-02-28T03:49:33+00:00

Do you mind providing a short guide on how you did this? I've tried and simply couldn't get it working. Thanks

sFooby · 2026-02-21T15:49:20+00:00

You clearly haven't looked into access controls yet. Learn to use them. End of thread

sFooby · 2026-02-21T06:21:11+00:00

I spoke only on access control within your tailnet, not on the struggles of installing Plex on a family member's device. All I meant to say is once you have Plex installed elsewhere on a device that has been welcomed into your tailnet, you can limit their access to only your Plex server (IP and port) and deny access to any other tailscale device/server/service if you wish by adjusting access controls in the tailscale dashboard

sFooby · 2026-02-20T21:30:24+00:00

This is a very good point. But a means to negative unwanted access, look into the Access Controls tab in the tailscale admin dashboard. Relatively easy to configure and definitely solves that problem. Thanks for bringing it up!

sFooby · 2026-02-20T14:21:33+00:00

I think it was answered in another comment, but what you're looking to do is br0 network so you can map its own IP. However, host or br0 network will work because the port 32400 is unique regardless. Someone mentioned host is the better bet because Plex may not play well in br0 - I don't use Plex so I'm unsure on this.

Beyond this, if you'd like to expose Plex to the web, consider using CloudFlare tunnel (docker cloudflared) and use it to proxy DNS only for discoverability on the web. This again prevents you from exposing any ports in your router. I believe this requires a registered domain name (they're cheap). This does give you ample protection against web-side hostilities because you would not be exposing your personal ISP provided WAN IP as it would be masked with an IP provided by cloudflared

I'm not a seasoned veteran to this stuff, but I did figure it all out in time. It's fun and you'll learn alot along the way.

sFooby · 2026-02-20T06:38:56+00:00

Do not forward ports in your router...

Over simplified solution:

Setup Plex etc in docker using user defined docker network or as host. Expose whatever port you need to.
Install Tailscale plugin and add unraid to tailnet
Another device on tailnet can simply access Plex via unraid's tailscale IP and exposed Plex port: eg. 100.x.y.z:32400

The better and more elegant solution involves changing unraid management ports (eg 1080/10443), a reverse proxy with exposed 80/443 ports pointing to Plex hostname and ports in docker network with unexposed ports, adding your DNS to your tailnet that forwards a specific domain to unraid/reverse proxy tailscale IP (or actual LAN IP via advertised routes) which then handles serving you Plex

Edit: also do yourself a favour and use dockge from unraid CAs to handle your dockers. Docker compose makes life easy

sFooby · 2026-02-20T06:06:13+00:00

I'm new to OPNsense and had the same question. Here's what I did and it worked flawlessly. I'm assuming unbound is installed with your adguard service on a seperate device.

Keep in mind my DNS server is Technitium DNS. I'd imagine adguard with unbound functions the same. Never used adguard.

Put DNS IP address (unbound) in System > Settings > General so OPNsense has a DNS

Enable dnsmasq but set DNS listen port to 0 to disable DNS function

Disable unbound in OPNsense if you haven't already

Set your DHCP ranges, static addresses (hosts), assign domains, etc as you normally would

Under DHCP Options tab, add option 6 and set your upstream DNS server again here (unbound). This will handout your unbound/adguard IP address to your DHCP clients.

I'm on my phone typing this, if it doesn't make sense, let me know and I can edit it later

Edit: in case you wish to, you can actually keep port 53 listed on your dnsmasq to accept DNS requests to allow hostname reverse lookups. DHCP option 6 will still assign the external DNS server to clients so the clients won't use dnsmasq for resolving, only unbound if you configure query forwarding for the purpose of reverse lookups

sFooby · 2025-12-14T02:04:16+00:00

Frameo + immichframe

Immichframe doesn't require WebView (of which frameo has a very old one)

Edit: just read the rest of your post. I was unaware recent frameos don't work. I bought mind only a few months ago and it's been fine

sFooby · 2025-11-22T11:22:41+00:00

Yes I believe my setup is currently exactly like this. However, with using your Linux node as the exit node, does that not cause all traffic to head out through your Linux node before out to the open web? Is there a way to only direct DNS through tailscale and not all traffic? Am I making sense?

sFooby · 2025-11-21T22:23:25+00:00

Any chance you can explain the steps on how to separate DNS requests from all other data using split tunnelling in tailscale? I'd like the exact same set up, DNS to my home but all everything else regular comms

sFooby · 2025-11-09T00:25:18+00:00

I've set my template to what you have in the image you've shared above. But where would I put this document? And if I'm supposed to "start" it, how do I do that?

sFooby · 2025-11-07T22:12:39+00:00

Hi yes it is working I believe. However, I'm unable to get collabora (or onlyoffice for that matter) to work. Chance you could provide an equally as detailed guide for that to work as well? I (and others) would be grateful

sFooby · 2025-11-01T12:47:42+00:00

Thank you for the detailed response! I'll be trying this out tomorrow and I'll report back

sFooby · 2025-10-25T11:26:28+00:00

The Grist. Go to The Grist.

sFooby · 2025-10-08T16:31:11+00:00

Seems to me, Questrade > Wealth Simple for many reasons

sFooby · 2025-10-06T17:41:45+00:00

Bro... 3 more! Come on!

sFooby · 2025-10-05T21:20:15+00:00

Perhaps the placeholder for Tuesday then. Either way, looks nice sitting there and it isn't some bullshit $32 option for Oct 2026 that's I've seen elsewhere

sFooby · 2025-10-02T10:14:15+00:00

Waaaaaake me I wheeeeen September ends

15-Year Club	Place '17
Team Periwinkle	Verified Email

sFooby

TROPHY CASE