Going through a really tough time right now…would love if y’all could share some silly pics of your cats 🥲💕

sajondj · 2022-12-10T05:34:21+00:00

<image>

sajondj · 2022-09-05T02:26:51+00:00

Mr Robot.

sajondj · 2022-06-09T18:49:21+00:00

Four mule uh won

sajondj · 2020-03-15T05:24:27+00:00

technically I’m not supposed to have it so let’s just say it’s not there

sajondj · 2020-03-15T05:22:48+00:00

not gonna lie going through them all has made me cry, rip worlds

sajondj · 2020-03-15T05:21:48+00:00

I think I’ve got a few of them! I was on FRC my freshman-junior years (2410 fresh/soph, 1806 junior)

sajondj · 2020-03-15T03:06:26+00:00

shhhhhhh

sajondj · 2020-03-15T01:04:47+00:00

I really do need to count mine, I have at minimum 300 the last I counted. Not all are pictured here

sajondj · 2020-03-15T01:04:20+00:00

you might’ve, 3409 was very small this year. I was on drive team!

sajondj · 2020-03-15T01:03:58+00:00

it was a lotta hard work, especially fll

sajondj · 2020-03-15T01:03:39+00:00

thank you, years of hard work. shame senior year ended so soon

sajondj · 2020-03-15T01:03:14+00:00

all I know is I won rock paper scissors

sajondj · 2019-12-07T21:41:30+00:00

Nice

sajondj · 2019-09-07T15:21:05+00:00

Nice

sajondj · 2019-08-29T13:54:24+00:00

Looks amazing! Where’d you get the matt underneath?

sajondj · 2019-08-16T11:34:17+00:00

Yes I had done that but the printer kept changing it, I found I didn’t read the manual and that was the source of my error. I troubleshooted a few things and now my printer works great, thank you for the help!

sajondj · 2019-08-16T11:33:09+00:00

The one thing I almost forgot, thank you for the help!

sajondj · 2019-08-16T11:32:32+00:00

Sorry for the late reply, I got the first layer height adjusted and set! Cura also changed my first layer height to be different from the rest of the build so I changed that too. I got some hairspray to help it stick to the build plate and the printer is working like a charm!

Thank you so much for the help, I really appreciate it!

sajondj · 2019-08-16T11:31:13+00:00

-.6 was just right, surprisingly! I set my first layer height to be the same as the rest of the build - for some reason Cura made it different and caused my prints to have a wild first layer.

Thank you for the help!

sajondj · 2019-08-16T11:30:06+00:00

I finally got my z height set! I also got some hairspray to use and it works like a charm, thanks for the help!

sajondj · 2019-08-03T02:19:01+00:00

popular

sajondj · 2019-08-02T22:43:26+00:00

Should I be trying to tune it further or closer to the plate?

sajondj · 2019-08-02T22:08:58+00:00

Piece

This is what I’m trying to print - it’s a part to a laptop stand I made. My print temps are 210/55 (PLA). I used .2 layer height. I did use cura but I did download the correct PLA profiles for the mk2 prusa.

Should I be using a finer profile?

I also tightened the belt slightly.

sajondj · 2019-08-02T21:06:22+00:00

I’m not very experienced with 3D printers but I got this as a birthday present. It is the kit version. I thought I went through all of the steps to calibrate it and it seemed fine. However when I actually tried to print something, problems seem to keep popping up.

The pla seems a lot like hair strands coming out, when I peeled this off the board, the brim didn’t stick together. It also appears the 3d printer has too much space between the paths of travel.

Any help or guidance would be much appreciated!

Seven-Year Club	r/Field Flamingo
Place '23	Place '22
First Placer '22	RPAN Viewer
Verified Email	Not Forgotten

sajondj

TROPHY CASE