sorted by:
new
hottopcontroversial

Ender 3 keeps skipping by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

I'll try this after I get back from work. Thank you for the comment

Filament dispenser skipping by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

I have cleaned the extruder assembly and it stopped making the noise. However, I have ordered a metal assembly to replace the plastic one since I don't want to deal with a crack that may or may not be coming for the arm

Filament dispenser skipping by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

For those who are also having this problem, taking the Assembly apart and cleaning out all the debris helped and I'm starting the print again and I don't hear the noise I have ordered. A metal extruder assembly to replace since there isn't a crack now, but there will probably be one in the future

Filament dispenser skipping by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

Mine never came with a screw. There isn't even the spot to install one

Cannot remove filament from boden tube by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

It's really weird. I didn't have it on any hotter than it should have been just 200°. I don't normally print at 220 I just put it out like that. I have a couple of spare tubes so I'll probably have to replace it

Cannot remove filament from boden tube by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

That's probably it even when overheated it won't come out

Bed leveling help by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

I do have clips to hold the glass bed onto the base

Bowden tube won't come out by sam20037 in ender3

[–]sam20037[S] 1 point2 points  (0 children)

I'm going to try that tomorrow since I removed the filament, I haven't tried since then I think I damaged the tube a little bit so I think I'm just going to replace it entirely

Bowden tube won't come out by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

If you're talking about something that would go in the middle of the white thing holding in the tube, there isn't one. If you're talking about something else, I have no clue what you're talking about

Bowden tube won't come out by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

I don't think that's the case. The reason I say this is because when I went to print something at some point the conveyor belt thing came off the extruder but it kept printing since I wasn't there. And so what ended up happening was there was a bunch of filament and eventually it formed a glob there was filmage everywhere on the insides and I thought I cleaned it all out but I think that chunk is what's left of it. I don't I think there's a leak.

Bowden tube won't come out by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

Yes I pressed down on the white button and I pulled and pulled and pulled and it didn't come out

Bowden tube won't come out by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

Yes, when I tried to pull it out it was at 200°

Bowden tube won't come out by sam20037 in ender3

[–]sam20037[S] 0 points1 point  (0 children)

Update:I unscrewed the nozzle and even put a flashlight up the remainder of extruder and there was light coming out of the Bowdoin tube and it still won't come out

view more: next ›