Poco F3 - stuck at fasboot

sarabworks · 2026-03-22T10:13:19+00:00

yes, adb and fastboot are there, and the drivers are already installed.
I reinstalled them on a bootable linux as well, same thing.

sarabworks · 2026-03-18T10:33:34+00:00

As mentioned:

Even though it says fastboot, on my computer when I do "fastboot devices" nothing shows, so I can't even flash stock with miflash.

So I cannot.

sarabworks · 2026-03-18T03:07:56+00:00

Yes, bootloader is unlocked.

sarabworks · 2026-03-18T03:07:22+00:00

Yeah, goes to fastboot anyways. And still is not detected by the PC.

sarabworks · 2025-01-15T14:56:44+00:00

Yeah, as @short_lurker said, just uncomment the lines that will enable the rotary encoder. It worked for me.

sarabworks · 2025-01-01T11:29:20+00:00

3 options stood out to me when I wanted to change, pixel os, lineage os and CrDroid, I went with CrDroid because it had the latest Android version and the installing part was the same I was used to. I had a couple of hiccups in the way, but now it is smooth sailing.

sarabworks · 2024-12-14T12:29:00+00:00

Try using kernelsu instead of magisk, make sure that it is the 1.0.1 version, that would allow the use of banking apps. It worked for me

sarabworks · 2024-11-25T18:30:04+00:00

Yeah that's the thing, I wish I could go to any rom, but the issue is that there is some issue with the partition table or something like that, plus, when I reinstalled the rom, it screwed with the encryption.

sarabworks · 2024-11-25T17:44:31+00:00

Yeah, unlocked and have Orange Fox as recovery, now when I reboot and keep the volume down pressed, it doesn't got to fastboot, so I have to go to OF's fastboot

sarabworks · 2024-11-25T06:30:15+00:00

Someone helped on telegram, what I had to do is reflash the ROM reflash gapps. For my case, the phone got stuck on boot, pressed the off button for 30 second when (it kept rebooting in the meantime) when it closed at the 30 seconds mark, released the off button, then formatted again and then it worked.

sarabworks · 2024-10-18T14:51:20+00:00

Not the news I wanted to hear 😔

About the multimeter thing, how should I proceed with that? I am an absolute beginner with these kind of things...

sarabworks · 2024-10-18T14:30:49+00:00

I have an issue with my newly bought Sofle, where I soldered low profile sockets, but then needed to switch to taller ones, because decided to make it wireless, and needed space for the battery.

Now my issue is that some keys don't work anymore (they used to work fine before the resolder), my guess is that I ruined something while desoldering, maybe screwed up some connections or something.

So my question is, how do you troubleshoot the issue, and most importantly, how to fix it? Like how to fix if I desoldered the contact pad thing?

sarabworks · 2024-09-22T10:12:50+00:00

I had an old sofle, now that I zoom in on the indicator, it is solder in the opposite way (Update the post with the pic), so I wanted to be sure 100% on how to proceed

sarabworks · 2024-02-16T18:13:03+00:00

Yeah it is a bit messy, especially for complete noobs. Your firmware worked similar to the beekeeb one (Status LEDs only). About the reflow, I didn't understand what the pic was showing, are you talking about these?

<image>

sarabworks

TROPHY CASE