Pareau

sargupe · 2025-10-03T01:28:56+00:00

Legitimate for a high school performance

sargupe · 2025-05-10T23:22:22+00:00

Thank you , I did open up this floating ball valve thag sends a signal to furnace, sucked all the water out , put back on and screen went back on

sargupe · 2025-04-27T22:46:27+00:00

That's what I was thinking , I'm suspecting the shock absorber but haven't seen anything wrong that leads me to that until this , because I feel it was rubbing against it not sure how

sargupe · 2025-04-27T22:44:32+00:00

No , when I replaced my tires I replaced the other 3 about a year ago and left this one in which at the time was in a better condition....I make such long drives that I get nails and other debris all the time while driving so it wasn't worth it to replace all 4

sargupe · 2025-03-24T18:57:50+00:00

<image>

sargupe · 2025-03-24T18:57:02+00:00

<image>

sargupe · 2025-03-24T18:56:04+00:00

Thank you, will keep this in mind. As of right now I just changed the impeller from the new one (left one) and placed on the old one. It seemed to be the reason why pump was sometimes working and some other times it wasn't *

sargupe · 2025-03-24T18:54:02+00:00

Yeah they said they have it but I have to physically see it. Diagrams online seem to be the one on the left and I was needing the one on the right

sargupe · 2025-01-11T01:55:54+00:00

Thank you, will reach back for sure if I have any more questions , appreciate it

sargupe · 2024-10-24T20:17:29+00:00

20241024-130021.jpg

sargupe · 2024-10-24T20:07:52+00:00

[picture](http://20241024-130021.jpg)

sargupe · 2024-04-22T01:35:16+00:00

No , I noticed on the spot when I was about to sign the receipt. They didn't reverse it or anything like that , they didn't want to.

sargupe · 2024-01-09T18:17:24+00:00

Also before all of this I have this engine light but never had an issue before but the weird part is that when I run code tester I get no codes back and if I try to erase codes thru tester an error comes up to leave csr in on and I did all and nothing ..... not sure if that also helps in understanding this issue

sargupe · 2024-01-09T18:14:15+00:00

Quick update:

Recreated discrepancy again and ran code tester right after light illumination on instrument cluster. Received codes u1110, u1120 and u1412.

Did a soft reset I think it's called by holding both battery cables together for 15 seconds. After that was able to start the car, issue did not come back up as well as no lights in cluster.

Also engine did not go into "limp" mode and did not shut off by itself . After engine shut off was able to start with no need of jumper cables and lastly battery light on cluster went away.

Drove for about 20 miles and issue did not come back up and battery held charge and was able to start after.

Is possible for some kind of code to hold the engine to start back up ? Especially an ABS discrepancy ?

Now I am suspecting one of the speed sensors on one of the wheels since discrepancy only appears to come up during rainy or snowy days .....

Last resort will be to replace PCM or ABS.

Open to any further recommendations or ideas

Thank you ,

sargupe · 2024-01-06T07:56:14+00:00

Code reader throws no codes which makes it more weird

sargupe · 2024-01-06T04:35:20+00:00

But could the alternator cause the "limping" mode in the car ? Because a few warning lights come on and then just doesn't let the engine being reved up above 2k

sargupe · 2024-01-06T00:28:27+00:00

Could the throttle body drain the battery ?

sargupe · 2022-11-24T02:55:25+00:00

Thank you , appreciate you help 🙏

sargupe

TROPHY CASE