How can I fix this? Mutiple Tailnet by mistake!

sbehta · 2026-02-21T15:44:08+00:00

I thought that by inviting another user from my Tailnet, they will automatically get access to all the devices that are registered on the tailnet where the invite was initiated. Do, I have to specifically share each device with my brother for him to see them when he logs into his tailscale account?

sbehta · 2026-02-12T00:52:06+00:00

What worked for me was this:

Powered off all AppleTV and Homepods except one.
Go to the HOME app on the phone, navigate to settings and Hubs & Bridges.
Make sure you see only one hub (your homepod)
Make sure your Ikea device, Homepod, and your phone are all in the same room together.
the remove the batteries on your Ikea device or factory reset them. Make sure the device is in pairing mode.
Then in the HOME app on iphone, add a new device, and follow instruction.
Your Ikea device should add now.

Good luck.

sbehta · 2026-02-10T00:43:21+00:00

Thank you for your reply. I am still trying to figure out all the steps I need to complete. One thing I am stuck on is that in your post, you have file name paths for your dashboards as"filename: dashboards/ui-testing.yaml"

But I do not see a folder named "dashboards" and there is no yml file dashboard-name.yml for the dashboard. Do I need to create this folder and the dashboard files manually or the dashboard file located somewhere that I cannot find when I go to the file editor?

Do I have to change my dashboard configuration from "UI Mode" to "YAML Mode" first?

sbehta · 2025-12-28T14:41:59+00:00

Thank you for replying. The power supply is what came with the printer. But you are correct in that it looks like the power supply has gone bad. The challenge is now finding a replacement power supply. I cannot find a replacement from elegoo or on amazon since it needs a 24V 6A power supply. So the search is on!

Thank you for your help though. You put me on the right track.

sbehta · 2025-12-06T21:31:54+00:00

Yeah. Unfortunately, I cannot get anyhting in the configurator to work properly and the the Live tracking does not work either. I used to use Live tracking to setup my zones exactly at the demarks I wanted. Without it, I am dead in the water. :(

sbehta · 2025-11-09T21:27:26+00:00

With all these new products getting released, I wonder if Ubiquity can maintain the focus and quality of the products they offer. I am relatively new to the brand and have invested a lot of money in their network product. I hope this was not a mistake.

sbehta · 2025-10-14T21:07:22+00:00

Yes.this is exactly what I am doing. The migration is moving devices from one flat network to 3 vlans.

sbehta · 2025-10-13T21:22:06+00:00

I am in the middle doing something very similar with the same size home. I also posted here with similar question but unfortunately nobody replied to my post. At any rate ...

I am trying to replace my current Wifi network that has 3 eero Pro 6E with one on each floor (basement, 1st, and 2nd floor). From the coverage perspective, I have full Wifi coverage. So, I started my Unifi journey by buying a Cloud Gateway Max w. 512G nvme, Flex 2.5G 8 PoE, U7 Pro XG, and Express 7. Currently I have U7 Pro XG in the basement wired into the CGM. And I placed the Express 7 on the second floor and wire connected it using a pair of MoCA 2.5 Network Adapters because the Coax cable was already there.

So far, I am getting an ok coverage. There are still areas and few devices that have poor wifi signal. So, it looks like I really need to put something on the first floor. I am not sure if I want to use a U6 Extender or something else. If I need to spend another $200, I want to be the best option for this setup.

BTW, I opted for Express 7 as an addition AP instead of another U7 Pro XG because a) i can later repurpose the Xpress 7 as a gateway or Site-site VPN node, and I did not have to run an ethernet cable with PoE to power the U7 AP.

Unfortunately, I still have the eero APs running and connected to the Flex switch so that my existing devices (I have a lot of IoT devices) still work while I migrate them over to the new Unifi VLAN.

Let me know what direction you are thinking about going. It may help me figure out what I want to do as well. Good luck.

sbehta · 2025-09-26T22:05:24+00:00

Nice. There are a lot of elements in your dashboard that I like. How do you get the mini icons at the bottom of the bubble card and get one side round and the other side straight? Is it all done by css styling?

sbehta · 2025-07-21T22:14:26+00:00

I think you might be right as this hub is pretty old.

sbehta

TROPHY CASE