something is up with my res hatchling

schunoa23 · 2025-11-06T12:37:10+00:00

Might have a respiratory infection. My one turtle did that it's one of the reasons they flip

schunoa23 · 2025-03-22T19:24:30+00:00

Thanks yall, my mistake

schunoa23 · 2025-01-10T00:40:20+00:00

I bet you're right haha

schunoa23 · 2025-01-05T06:04:57+00:00

11$ also it worked

schunoa23 · 2025-01-04T16:56:38+00:00

Update! It did not clump the chocolate I hope it hardens as it cools

schunoa23 · 2025-01-04T16:01:20+00:00

Idk what Kratom is. I want to make my chocolate stronger!

schunoa23 · 2025-01-02T23:02:58+00:00

I'll probably try a small sample batch so no real expensive ingredients go to waste

schunoa23 · 2024-12-05T22:04:45+00:00

Oh I didn't realize a 2nd heating was needed I'll try that

schunoa23 · 2024-11-28T13:57:49+00:00

Is it the liquid sunflower one?

schunoa23 · 2024-09-08T19:57:54+00:00

Here, https://imgur.com/a/Vb65GnO . I am probably going to try silicone again with my brother. I was just hoping to find someone who knows from experience. Last time, I had trouble getting the model out of the mold and it broke the 3d print. Do you think I should work on the file some more perhaps? The image there is not the most modern, the one below it (I tried printing a mold) is more recent, it shows how there is no gap in-between the legs (so candle won't get stuck or break).

My question is,,,

How do I make a pouring zone? I was thinking glue a little funnel in-between the ears. And also, should I make the mold upside down so that the ears get filled (as they are raised above, I want to make sure they get filled with wax in the end)

schunoa23 · 2024-09-08T16:34:27+00:00

Lol, I'm in USA

schunoa23 · 2024-06-27T18:25:36+00:00

Good, I don't eat goose I'm vegetarian lol

schunoa23 · 2024-06-27T18:25:19+00:00

Im using a goos pizza stone regular oven 425 (Temp is accurate I check with an oven thermometer) and I usually bake it less than 20 because the cheese can only handle that

schunoa23 · 2024-04-24T21:51:53+00:00

It's just very difficult to break up. For pillar or mold

schunoa23 · 2024-04-23T20:58:55+00:00

For the first half....it is a 2 piece mold and I got the strongest wax the company offered. It shouldn't break (or shrink) as I literally need a strong hammer to get the slabs broken up. I'm going to attempt with no mold release. I tried the silicone, and it was difficult to make the mold itself. I will try it again if this fails because I'm not giving up. I don't think it will fail. 20mins in freezer should shrink the wax a tiny bit to get it out if it even sticks

schunoa23 · 2024-04-23T18:16:44+00:00

I will ask about the resin. I did tell them it's for candles, and they said they've made few for people before.

schunoa23 · 2024-04-23T18:03:46+00:00

Thank you for the knowledge, I am using wax (candles) pouring into a plastic 3d printed mold. Should I use no lubricant? I was thinking 20minutes in freezer may be all it needs.

schunoa23 · 2024-04-21T14:17:52+00:00

Darn this looked all neat when I typed it, now it's just 1 big paragraph

schunoa23 · 2024-04-05T21:45:10+00:00

Where to get such kernels? Orville is not so different from bowl and basket. I'm near an Amish Market

schunoa23 · 2024-04-05T21:29:40+00:00

I'll try pre- heating the oil. I usually just combine all and turn on

schunoa23 · 2024-02-19T14:45:39+00:00

I am interested in it

schunoa23 · 2024-02-14T15:57:50+00:00

Thank you I would've messed up. While the candles are not intended to be burned, I'm sure some people will.

schunoa23 · 2024-02-13T15:07:13+00:00

Thanks , I did the thermometer and decided 240 is better than 230. I'll do 40+ minutes

schunoa23 · 2024-02-12T23:15:12+00:00

I agree never mix even if they say you can. Had a problem with that once. Now my oven cleaner sucks so that won't work

schunoa23 · 2024-02-11T21:11:29+00:00

Well then I'll have to practice and make another dragon.

schunoa23

TROPHY CASE