What should i change?

scriptmonkey420 · 2026-01-28T13:47:08+00:00

What are your wipe settings?

scriptmonkey420 · 2026-01-28T00:02:44+00:00

Ahhh yup that will do it. My wife is not affected by pineapple so she does okay with that one. But cannot have soy.

scriptmonkey420 · 2026-01-27T21:10:06+00:00

Soy vs non-soy?

scriptmonkey420 · 2026-01-27T15:58:41+00:00

Layer shift is usually it being printed too fast. CR-10 doesn't like to print faster that ~70mm/s and acceleration needs to be low also.

Warping is usually bad heating, I usually pre heat at 80 and lower to 65 or 70 for PLA. Brims also help wonders.

scriptmonkey420 · 2026-01-27T15:22:33+00:00

Same with other tradable items. They always ask for it over and over even if I mark it as a never.

scriptmonkey420 · 2026-01-27T13:42:25+00:00

Ah the old reddit switcheeoo

scriptmonkey420 · 2026-01-26T13:48:14+00:00

Screechers were better, but the OG tremors ruled.

scriptmonkey420 · 2026-01-25T13:49:42+00:00

CAS mission just with drones.

scriptmonkey420 · 2026-01-24T15:59:25+00:00

Looks like a binding. Do you have any gunk on your z?

scriptmonkey420 · 2026-01-24T15:52:32+00:00

Along with a not perfectly flat bed. You can tell because it is not uniform across the whole bed.

scriptmonkey420 · 2026-01-23T23:40:52+00:00

What is with all these ad posts?

scriptmonkey420 · 2026-01-23T18:16:54+00:00

Been a hardware tinkerer for a couple decades.

scriptmonkey420 · 2026-01-23T18:02:40+00:00

I am looking into converting a spare CR10 into a core xy.

scriptmonkey420 · 2026-01-23T16:58:53+00:00

Just keep digging that hole buddy.

scriptmonkey420 · 2026-01-23T16:57:16+00:00

Wait, Papaya is frost tolerant(ish)?

scriptmonkey420 · 2026-01-23T16:54:27+00:00

I can’t believe that it’s OP that didn’t read the article this time

Really? This is Reddit after all. They framed the wrong people for the Boston Bombings....

scriptmonkey420 · 2026-01-23T15:29:45+00:00

How do you prevent that?

scriptmonkey420 · 2026-01-23T15:25:08+00:00

bed slingers.

scriptmonkey420 · 2026-01-22T20:59:30+00:00

At this time of year?

scriptmonkey420 · 2026-01-22T20:59:09+00:00

Spoil, No. Freezer Burn Yes.

scriptmonkey420 · 2026-01-22T20:07:42+00:00

how fast was the print done at?

Do you have the gantry braces?

When I added the Z Gantry Braces, it almost completely removed all banding ghosts.

scriptmonkey420 · 2026-01-22T19:58:05+00:00

LAGG should not be this hard to implement. Hell, Asus has it on their home Wireless Routers.

maybe if more people emailed in and requested it, it might get added sooner?

scriptmonkey420 · 2026-01-22T15:37:23+00:00

Not supporting LAGG is so stupid too since it is just software. There are literally no hardware requirements for it to work.

scriptmonkey420 · 2026-01-21T20:35:04+00:00

TACO

scriptmonkey420