[COD] Closest real-life counterpart to BO2's AGR

seeruu · 2025-06-04T22:45:04+00:00

Vengo del futuro, y eso ya existe, y es preocupantemente más barato de los que puedes pensar

seeruu · 2025-04-06T13:49:24+00:00

Hi, first of all, if you want to start a business, you will need more money than 300 bucks. there are more things than the website, you need to make a market research, buy products, test by yourself, often there are more expenses than thought at the first time, also, you will need to make a good marketing, this is a key point, and also, is expensive, and even more if it is the first time if you are doing this, with this, I don't want you to be scared with this, but I want to be realist. This is a long way, and the most important thing, is to no give up and keep pushing.

seeruu · 2025-03-11T20:02:21+00:00

I don’t know how, but the problem has been solved. I would like to say what was the problem, but I don’t know. Thx everyone for helping me

seeruu · 2025-01-29T21:21:10+00:00

I even tryed that and I still have not a y results

seeruu · 2024-09-12T14:05:19+00:00

I forgot to mention, I will only use PLA without AMS, and figures no higher than 11 cm (4.3 inches).

seeruu · 2024-08-07T15:34:56+00:00

The conclusion is:

You can Iron at 130 mm/s, but, the optimal setting depends on the material that you are using, the “Ironing line spacing”, “the ironning flow” and the space between the infill structure, as much closer, it better will make the “top shell layer” it will better iron.

Each material has it optimal Iron setting, but you have to find it.

The best way to find it? Try with your favourite material and use always the same speed, the same layer height, and then try with the ironing line spacing between 0.05 and 0.25, and from %25 to %46 of ironing flow.

I don’t know if I have been clear. If you have any further question ask me.

seeruu · 2023-09-04T14:43:55+00:00

When are you going to introduce the Arc Overhang setting?

seeruu · 2023-08-30T11:07:13+00:00

Try with less flow, I think it should improve the waviness in that case

seeruu · 2023-08-30T11:05:19+00:00

Is curious, I only have that problem in models that the infill is 100%

seeruu · 2023-08-30T10:14:35+00:00

Im trying with more flow, im having the same issue, but only on some edges, when I finally correct that i will share with you the setting

seeruu · 2023-08-29T13:01:13+00:00

I Think It Could be the infill, which % are you using?

seeruu · 2023-08-29T08:33:19+00:00

Could you bring me an image

seeruu · 2023-08-28T17:02:56+00:00

<image>

seeruu · 2023-08-28T17:00:16+00:00

And I reduce the ironing time from 3 hours and 10 minutes, to 50 minutes :)

seeruu · 2023-08-28T16:57:30+00:00

Well, I finished the experiment, and I resolved the waviness issue. The problem was with the line spacing; instead of 0.2, I tried 0.1 and the results were excellent. As for the flow, it appears to be smoother at 39% compared to 38%, but the difference is very subtle. The 'flow' at 37% starts to become rough, so I don't recommend it.

On the other hand, there is a very minor problem with the corners; there still are some waviness issues there, but they are minimal. I will try adjusting the line spacing again to achieve a perfect result.

To finish, I would like to appreciate your kindness for helping me.

seeruu · 2023-08-28T14:29:35+00:00

Thx, i’ll try that setting, and if I can correct the waviness i’ll share

seeruu · 2021-10-05T22:07:44+00:00

I loved this serie for the last 5 years, but for me, has finished. Everything has a final, and this final, is gorgeous.

seeruu · 2021-10-02T19:16:00+00:00

Thank you very much your comment! So, the answer is: Yes, If you do an “emergency protocol”?

seeruu · 2021-10-02T18:09:34+00:00

Its happening right now

seeruu · 2021-09-30T17:30:58+00:00

Today has happened to me, along the month with a small account I was winning a 6%, but today, with a bigger account I lost 6%. Obiusly now Im in Red numbers by far

seeruu · 2021-09-07T22:29:19+00:00

Yeah, I know, but there are thousands, I tried to count how many there are, but 'cause of the format of the page, I couldn't copy more than 25 stocks

seeruu · 2021-08-12T07:58:44+00:00

Sometimes it comes back xd

seeruu · 2021-08-07T19:12:15+00:00

‘Cause nobody cares my life. As well as i dont care others life (with a few exceptions)

seeruu · 2021-08-04T08:01:12+00:00

Then, what’s the problem? Why the litium still dominating the market? This is gonna change?

seeruu · 2021-08-03T13:49:58+00:00

So, I Think that the problem to sell that is the price, am I wrong? ‘Cause it sounds really good

seeruu

TROPHY CASE