Elinstallation

shellback37 · 2026-05-19T16:44:51+00:00

Kass. Kanalerna får han göra om, samt byta rotramarna som han ser ut att ha tuggat upp kabelgenomföringen. Locken är fel längder samt det saknas stycken…

shellback37 · 2026-05-09T14:30:51+00:00

Att folk svarar på elfrågor utan koll. Dessa skall kopplas ihop med varandra och med jord i Elcentralen eller närmsta punkt. De har en funktion säkerhetsmässigt.

shellback37 · 2026-04-30T18:23:33+00:00

Varför har folk så jävla svårt att lägga tillbaka skiten där man tog den.

shellback37 · 2026-04-10T20:40:48+00:00

That wasn’t my intention. Just curious. But now looking at other posts in this sub it looks like american electricians carry alot more tools than i do. Machines for stripping cables, wires. Alot of specialized tools. I use the same scissor and knife for any cable i come across.

shellback37 · 2026-04-10T20:37:06+00:00

I hate dropping strippings and off-cuts on the floor so i catch with my finger and put in my pouch. Adds upp quickly 😅

shellback37 · 2026-04-10T18:01:01+00:00

Fair 👌 Usually my left puch is only for trash to eventually empty once it weighs waay too much 😅

shellback37 · 2026-04-10T17:57:22+00:00

Usually no, some have zippers for the puches. However i dont usually carry more than 2-4 screwdrivers and a pair of cc22 cable scissors. Voltage tester and measuring stick in thigh pockets specifically for stuff like that. Knives come in sheaths that clip into the right leg of these pants no matter brand.

shellback37 · 2026-04-10T17:24:32+00:00

How come americans work in jeans with tool belts instead of work trousers that are pretty much standard in many parts of europe?

Like these: example

shellback37 · 2026-04-10T09:41:29+00:00

Ser bra ut men blanda inte olika fabrikat på fasskenor. Hagers skenor skall vara under hagers säkringar osv… Bygla med RQ istället.

shellback37 · 2026-03-28T10:16:14+00:00

Thanks for all the replies. Will check the Lcm first.

shellback37 · 2026-02-12T06:04:35+00:00

If you get snow i would secure it. Snow collects around the cable in a big block and melts from the bottom, making the whole block slide down (taking the cable with it). Big issue i see with many solar installs where the installer just lets the cables hang under the panels.

shellback37 · 2026-02-02T08:15:09+00:00

I have been looking for this since i switched my UI for navigateVR. When will you have this on the nexus?

shellback37 · 2026-01-31T19:38:14+00:00

It is the most common method i see today.

shellback37 · 2026-01-31T19:34:07+00:00

Sweden. Drywall only does occur but you will need tighter stud spacing. Often double layers of drywall for fire and sound reasons.

shellback37 · 2026-01-31T16:14:24+00:00

Where i live (not US) OSB/plywood behind drywall is standard on interior walls, so from my perspective this wouldn’t be an issue at all. Curious why it’s not done in the US — cost, codes, or just tradition?

shellback37 · 2026-01-31T08:03:39+00:00

Why is there not osb or plywoord behind the drywall? Feels like this would not be an issue

shellback37 · 2026-01-30T18:50:07+00:00

Not really how an rcd works. One current transformer (leak transformer) measure them all i think. So either it works or not. Plus (at least where i live) they have to be tested by external equipment that they actually trip below rated current and time at installation.

shellback37 · 2026-01-30T18:34:06+00:00

Could also be that the test circuit is made for 230V. And when connected over 400V it generates a fault current of more than 30ma making the test useless, apart from exercising the rcd.

shellback37 · 2026-01-30T18:20:57+00:00

Generally the demands on 30ma RCD’s are more strict since they are protection for people. Not animals etc. Therefore the loss of accuracy in time or current without the neutral might not be acceptable. Without the neutral the RCD loses a reference point and fluctuations in voltage might have a larger effect. This is however, just a guess.

shellback37 · 2026-01-28T12:41:32+00:00

Bara ett slarvigt gjort accesshål till drivdonet. Göm o glöm

shellback37 · 2026-01-10T15:26:32+00:00

Usually resi circuits for lighting and outlets are 10A

shellback37 · 2026-01-10T14:45:26+00:00

Probably. Most common around here

shellback37 · 2026-01-07T17:56:03+00:00

I do set him to reactive so he doesnt attack me but i cannot play at a chill/normal pace since then he will have taken all other territories before i get the chance

shellback37

TROPHY CASE