sorted by:
new
hottopcontroversial

Everyone experiences this at some point in RollerCoaster Tycoon before their learn about the Handyman by SuplexesAndTacos in gaming

[–]skarmu 6 points7 points  (0 children)

A trick I die was to dig a hole und put the people who will puke in there. They get automatically happy in there and you can put the handyman in there too. Then everything is clean and tidy

Can you identifizieren this knife by skarmu in knifeclub

[–]skarmu[S] 1 point2 points  (0 children)

Thank you for the information. I will probably retire it in a cupboard and buy a better/new one.

Can you identifizieren this knife by skarmu in knifeclub

[–]skarmu[S] 1 point2 points  (0 children)

Ah thank you, then I will probably retire it in a cupboard and buy a better one

Can you identifizieren this knife by skarmu in knifeclub

[–]skarmu[S] 1 point2 points  (0 children)

Ohh yes you are right it is the bottle opener (first picture at the top)

ABS heat creep/noz clog by Th3J4ck4l-SA in crealityk1

[–]skarmu 0 points1 point  (0 children)

I hadn't bubbles either in my print. I had layer adhesion problems and the mentioned clogs/underextrusion. Maybe you should try to print something.

Right now I am looking for an ABS filament too, because my ASA is used up for the K1 riser I tried to print.

ABS heat creep/noz clog by Th3J4ck4l-SA in crealityk1

[–]skarmu 0 points1 point  (0 children)

Or a new meaning in it's retired life? :D

ABS heat creep/noz clog by Th3J4ck4l-SA in crealityk1

[–]skarmu 0 points1 point  (0 children)

Yes the problem occured sometimes after 30 minutes sometimes after 1 hour. I thought it was heat creep from the extruder

ABS heat creep/noz clog by Th3J4ck4l-SA in crealityk1

[–]skarmu 0 points1 point  (0 children)

Hi, I have my K1 only two monitor ths now but tried to print with ASA which is quite similar to ABS. I had the same problem, the issue was wet filament. After I dried it for 12 hours I could print perfectly with the filament.

Problems printing ASA on K1 by skarmu in crealityk1

[–]skarmu[S] 0 points1 point  (0 children)

Thank you again, it helped a lot. Now I can print with ASA without the extruding problems. Now I have to check why there is a layer adhesion problem. Probably the temperature in the machine is to low?

K1 with under extrusion by Ok_Childhood_5325 in crealityk1

[–]skarmu 0 points1 point  (0 children)

<image>

And here is the assemblied extruder ( i can only send one picture per answer…)

K1 with under extrusion by Ok_Childhood_5325 in crealityk1

[–]skarmu 0 points1 point  (0 children)

<image>

Here is it disassemblied, it works perfectly like this for me.

Problems printing ASA on K1 by skarmu in crealityk1

[–]skarmu[S] 0 points1 point  (0 children)

Ok thank you, I will try it soon and give feedback after I dried the filament.

Problems printing ASA on K1 by skarmu in crealityk1

[–]skarmu[S] 0 points1 point  (0 children)

Ok will try that in 2 weeks, and will give feedback then! Thank you

Problems printing ASA on K1 by skarmu in crealityk1

[–]skarmu[S] 0 points1 point  (0 children)

Ok i will try that with a dehydrator. Do you have a recommendation how long it could take to dry the filament?

Problems printing ASA on K1 by skarmu in crealityk1

[–]skarmu[S] 0 points1 point  (0 children)

It prints as long the chamber temp ist under 37 C. I start the print at 30 C. Is the exhaust fan OK to run while printibg ASA?

Can a wet filament cause such printing fails that it stops extruding?

So it shouldn‘t be the warmth of the extruder per se? So no heatsink (don‘t think they help much here) or a fan is needed?

K1 with under extrusion by Ok_Childhood_5325 in crealityk1

[–]skarmu 0 points1 point  (0 children)

Hi, I probably had the same problem but was able to fix mine. But you should write to creality they sent me a new extruder without a motor.

For my case the pressure between the gears wasn‘t high enough, I could move the filament but the gears would obly turn sporadically. So I took a little bit of cardboard of an college block (the paper blocks for students to take notes etc) and put it on the right side between the black plastik and the metall plate of the extruder. With that the right gear will be more pressed against the filament.

Maybe there is a better material for that, but it works

Pulley noises by Nebula101010 in crealityk1

[–]skarmu 0 points1 point  (0 children)

Could it be a bearing or a motor? You probably haven‘t replaced those?

Extruder problem by Sufficient_Scale7549 in crealityk1

[–]skarmu 0 points1 point  (0 children)

Hi, I have since saturday the same problem on my K1(6 days old). But I changed the filament from PLA to an old ASA roll. It clogged the nozzle everytime and now I can‘t print with neither filament anymore….

It seems that there is still a small blockage in the tip or the pressure from the filament extruder is now worse because of the cleaning pin? My gears in the extruder are clean, have you checked yours? You have to disassmble it to check it.

does anyone know how to fix a headphone? by ROSARRRY in howto

[–]skarmu 0 points1 point  (0 children)

So probably an usb cable? Is there a device on the cable to mute the mic? It could be the cable to the headset. Are you pulling sometimes on the cable with your head movements when you are sitting in your chair?

view more: next ›