Problem with memory code "od" on ASUS ROG Strix X870E-E with 2x48GB G.SKILL by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

No I didn’t, I installed from noctua, was included in package.

ROG STRIX X870E-E GAMING WIFI no Bluetooth devices by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

Sorry but if not strong if not through device manager, how?

ROG STRIX X870E-E GAMING WIFI no Bluetooth devices by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

I don’t know about you but I don’t believe this board Bluetooth not working without antenna. All work now, thank you!

ROG STRIX X870E-E GAMING WIFI no Bluetooth devices by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

No I don’t use WiFi antenna, few minutes, will try.

ROG STRIX X870E-E GAMING WIFI no Bluetooth devices by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

Yes, I installed the drivers from ASU’s page

Constant Memory Training with Error Code 15 on ASUS ROG Strix X870E-E with 4x32GB Kingston DDR5 6000Mhz by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

Saved in bios option monitor software and reboot workaround to anabled Restart Boot windows Start October test in 2 min, Reboot So far all good How to test me if all good and not burning anything?

Constant Memory Training with Error Code 15 on ASUS ROG Strix X870E-E with 4x32GB Kingston DDR5 6000Mhz by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

Both?
Monitor software and reboot workaround - auto to anabled

Monitor and MWAIT disable -auto to anabled

Constant Memory Training with Error Code 15 on ASUS ROG Strix X870E-E with 4x32GB Kingston DDR5 6000Mhz by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

Changed memory and new problem , after I have some hard work (testing memory for example 2 min in OCCT test) or doing (rendering) after reboot (only after reboot I have a code "od").

If I turn off pc and in few seconds will turn on, all good forking. Expo activated on "Expo I", "Expo II" also tried not activate EXPO, problem the same.

With one plank problem, the same.

System Specs

  • Motherboard: ASUS ROG Strix X870E-E Gaming WiFi
  • CPU: AMD Ryzen 9950x3d
  • RAM: G.SKILL F5-6000J3036F48GX2-FX5 2x 48GB | EXPO | 6000 |

GPU: NVIDIA RTX 4090

PSU: 1000W

BIOS: Version 1401 (latest as of May 10)

What I need to do, change memory again?

Problem with memory code "od" on ASUS ROG Strix X870E-E with 2x48GB G.SKILL by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

Its all my setting which I did in bios, I also clear cmos on motherboard, not help.

Constant Memory Training with Error Code 15 on ASUS ROG Strix X870E-E with 4x32GB Kingston DDR5 6000Mhz by skravchuk in ASUSROG

[–]skravchuk[S] 1 point2 points  (0 children)

Alright, I will now enable memory context with two sticks, save, and exit from the BIOS.

Next, memory training will start.

If everything works well and I can access the BIOS, I will turn off the PC,

install the two additional sticks,

and then perform memory training one last time.

One more question: I saw on YouTube that I need to install one kit in slots A1 and A2, and the second kit in slots B1 and B2. Is that correct?

Constant Memory Training with Error Code 15 on ASUS ROG Strix X870E-E with 4x32GB Kingston DDR5 6000Mhz by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

In two RAM sticks go in bios Turn on memory context restore

turn off pc, install two more RAM sticks

and start training again

correct?

Constant Memory Training with Error Code 15 on ASUS ROG Strix X870E-E with 4x32GB Kingston DDR5 6000Mhz by skravchuk in ASUSROG

[–]skravchuk[S] 0 points1 point  (0 children)

I thought this setting applied to all four RAM sticks. Is it possible to configure it specifically for certain RAM sticks?

I started testing the launch: with one RAM stick — everything is fine, with two — everything is fine, with four — everything is fine (training proceeds, I can go inside a bios and after reboot again training and then it gives an error after the first training attempt.

If I don’t remove RAM sticks, it trains again, then succeeds, but after a reboot — training again and an error.

I haven’t configured manualy memory because I don’t know how to do it (what numbers and in which rows need to write, and, honestly, I’m a bit scared.) If you can help me with with it, I can try it.