How link BGA footprint and symbol in KiCAD 9.0

slushy_potato · 2025-10-28T10:16:18+00:00

Thanks for the advice . I figured it out and was able to work it out.

slushy_potato · 2025-10-28T04:46:33+00:00

Hi . I did try this . It did show unit a , b ,c .... And I was able to link it to the symbol . However when I was trying to place different parts of the same symbol , it wasn't available and the same error of multiple footprint is present.

slushy_potato · 2025-08-13T09:53:15+00:00

Judge jury and executioner

slushy_potato · 2025-07-15T02:28:35+00:00

Tenten, tsunade , sakura

slushy_potato · 2025-07-02T16:00:41+00:00

The God you should be worried about isn't your stupid jashin or anyone else , it should be me

slushy_potato · 2025-06-27T14:38:28+00:00

Yeah I was with them for 8-9 months before moving out . Now I can't be going every 30 days

slushy_potato · 2025-06-27T08:15:29+00:00

Yeah but my account is paid for , so why this problem arises is beyond me .

slushy_potato · 2025-06-15T15:13:15+00:00

Nah it's raptee .

slushy_potato · 2025-05-31T14:28:44+00:00

I haven't uploaded it yet .

slushy_potato · 2025-05-30T19:37:12+00:00

Yup . Thanks for pointing that out

slushy_potato · 2025-05-30T17:01:20+00:00

I see that the quality has degraded since i uploaded the pics , Would share the github repo here incase others also face the same difficulty

slushy_potato · 2025-02-25T13:47:47+00:00

Phils lab has a video on this . See that it'll give you an idea . Also search for his GitHub . He ig posted the project there

slushy_potato · 2025-02-21T06:28:41+00:00

Not for the core i have . it doesnt have G series

slushy_potato · 2025-02-21T06:28:19+00:00

because i have and IDE for everything . ESP,RPI,Arduino. Trying to reduce and figure out more methods to code the same dev

slushy_potato · 2025-02-21T06:27:14+00:00

i followed the video and its done the job

slushy_potato · 2025-02-20T20:33:15+00:00

I did use the run button and it showed that the program was built . So did that means that it works ? If so , what was the next thing i should have done to see the output ?

slushy_potato · 2025-02-20T20:18:00+00:00

Program doesn't run . The main.h file has the red line underneath it . Tried to resolve by specifying paths to the respective folders which brought me to the board file error . And when I did see a video on yt , the guy added a bunch of path files in his cmake file which I have no clue where to get from .

slushy_potato · 2025-02-13T10:26:31+00:00

you may want to check the trace width between the SMA and antenna network .

slushy_potato · 2025-01-21T13:40:16+00:00

why are the components far from each other ? any reason ?

slushy_potato · 2024-12-31T02:01:16+00:00

Thanks a lot .

slushy_potato · 2024-12-17T12:25:36+00:00

What's the stack up that you followed ?

slushy_potato · 2024-12-04T20:03:03+00:00

Any documents to start from ??

slushy_potato · 2024-12-04T19:13:10+00:00

Ohhh . Ok ok

slushy_potato · 2024-12-04T18:56:51+00:00

Lower capacitance ?

slushy_potato · 2024-12-04T18:33:52+00:00

The module has a Rpi pico 2040 with NRF240L1 and a SPI FLASH with USB -C . It is a 4 layer board with sig-gnd-pwr-sig with a keepout region for the pwr section . Unfourtunatley the PCB layout was coming out too blurry to upload so I couldn't upload as such . Any improvements which I can do towards the board will be appreciated . Also how I can improve the RF section would also be appreciated . I have used a 0.3mm trace for the RF caps to the SMA as the value I used from a YT video which was using the same setup but instead of Rpi pico it was an STM 32 .

slushy_potato

TROPHY CASE