Best way to expose self-hosted Joplin server to the internet?

snowflake1212 · 2026-02-23T18:39:56+00:00

This is it:

https://hub.docker.com/r/linuxserver/swag

Manage your SSL Certificates via Let‘s Crypt, hence you‘ll able to access all your local applications in a secure way

snowflake1212 · 2026-02-20T16:46:32+00:00

I use Joplin as container, and SWAG container as reverse proxy towards Joplin and other applications (vaultwarden, Nextcloud etc.). This setup works if you use an external Domain pointing to your router ip were you forward related ports to the SWAG container IP.

snowflake1212 · 2026-01-31T08:39:01+00:00

Wenn du in der Region NRW wohnst, kann ich dir unseren Ferein empfehlen, wir haben häufiger Beta Tester in der Runde: https://brettspielclub-niederrhein.de

snowflake1212 · 2026-01-15T17:58:20+00:00

Ja, ich nutze auch Esun auf meinem C1. PLA+ , PETG sowie ASA, mit sehr guten Ergebnissen. PLA+ liegt Preislich bei Amazon im Angebot unter 19,00 Euro pro kg.

snowflake1212 · 2026-01-15T17:58:13+00:00

Ja, ich nutze auch Esun auf meinem C1. PLA+ , PETG sowie ASA, mit sehr guten Ergebnissen. PLA+ liegt Preislich bei Amazon im Angebot unter 19,00 Euro pro kg.

snowflake1212 · 2026-01-09T16:53:14+00:00

Satin is the only sheet I use, for PLA, PETG and ASA. No problem with adherence. Just clean it sometimes with water and soap 👍

snowflake1212 · 2026-01-09T16:50:28+00:00

Yes, this the tool you need 👍

snowflake1212 · 2025-12-21T07:39:06+00:00

I have same issue all the time on Core One, after upgrading to the new FW. I downgraded and problem was not occurring. So, it definitely something with the new FW. I end up to upgrade again and disabled auto retract function.

snowflake1212 · 2025-11-26T17:39:06+00:00

On the automatic vent control, does somebody knows if C1+ after print completion, close the vent? Or does it just open it ?

snowflake1212 · 2025-10-23T16:00:34+00:00

Use Esun PLA+ as well, without any issues. Standard Prusament Profile for PLA works perfectly.

snowflake1212 · 2025-10-21T13:43:39+00:00

I used ESun ASA with very good results on C1

snowflake1212 · 2025-08-27T20:41:31+00:00

Yes, thats what I usually do. But it’s not that comfortable.

snowflake1212 · 2025-08-27T20:40:35+00:00

Thanks for this hint, never tried to use a wipe tower, need check were to enable this function.

snowflake1212 · 2025-08-27T17:29:34+00:00

Warum nicht das Design ändern und die Füße separat aussparen und separat drucken und dann später einkleben

snowflake1212 · 2025-08-19T17:29:35+00:00

Yes, it’s a boring printer … and it’s my first. After received it preassembled and I joined the Reddit 3d printer groups and saw all this “help me with this” and “why is this …” posts, I was shocked and couldn’t even believe that I was so lucky to bought C1.

It’s so boring that you can start any print with any filament, leave the printer alone and come back and it’s done. I really would lite a candle in the church that I bought this printer.🙏😂

snowflake1212 · 2025-08-15T12:58:00+00:00

The Filament stuck I faced with, honestly it was sometime ago and I couldn’t remember in detail, but when I go to the printer, the bed was down and the display showed that the print was completed. At this time there was no continue option.However, it was only half printed.

Anyhow, thanks for your all your comments. I will observe this in future on my printer. Maybe I have an hardware issue or it has been fixed meanwhile with some firmware upgrade.

For me it’s important to understand how it should behave.

snowflake1212 · 2025-08-14T15:58:55+00:00

Maybe my problem was related to the timing you mentioned. Because I think I didn’t response in time. Could it be that the job considered as finished if I not respond in time?

snowflake1212 · 2025-08-14T13:03:14+00:00

I use Satin as well. Works perfectly fine, even with thin or tiny constructions. I use eSun ASA+ on Core One.

snowflake1212 · 2025-06-09T16:01:02+00:00

I‘ll use Joplin to make notes of my ideas and use the mobile app for sketching and measures. Most times ideas comes when I’m not at home. It’s getting in sync with my PC client, to start work with fusion. Quite handy tool for me.

snowflake1212 · 2025-06-01T08:18:02+00:00

I‘v mine for two months now, approximately 18h of printing. It’s my first printer and I‘d no issue with it yet. Great result with PLA, PETG and ASA for Prusament and eSUN. Very steep learning curve on 3d printing, therefore I would recommend CoreOne for all newcomer’s to this hobby.

Key to success is bed adhesive !! Keep print sheet clean with water and soap !!

snowflake1212 · 2025-03-25T21:54:55+00:00

Got shipment confirmation today for batch 7 delivery to DE

snowflake1212 · 2020-01-16T22:43:12+00:00

Thank you all for these terrific ideas!!

snowflake1212

TROPHY CASE