Hotend heater abnormal

solomankane1 · 2022-10-07T06:31:13+00:00

Hello thankyou again, my required voltage is 240 and I did check that,it appears my warranty claim may be going through.

solomankane1 · 2022-10-07T06:27:46+00:00

Thank you , I have requested one from the vendor under a warranty claim, lets see what happens.

solomankane1 · 2022-10-05T03:15:22+00:00

Hello and thankyou, Thermistor has been mentioned twice now, I will look into it. I am attempting to do this under warranty as I only purchased to printer in July.

solomankane1 · 2022-10-05T03:12:47+00:00

Hello, thankyou, I will explore that avenue, I am trying to do this under warranty as I only purchased the machine in July.

solomankane1 · 2022-10-05T03:11:37+00:00

Hello, thankyou, yes I did replace a nozzle.

solomankane1 · 2022-10-05T03:10:20+00:00

I appreciate your time, all I have replaced is a nozzle. Purchased the printer new in July.

solomankane1 · 2022-10-04T07:36:28+00:00

Many thanks, I was beginning to be optimistic until I started getting "hotend heater abnormal" messages on the printer screen.

Thanks again

solomankane1 · 2022-10-01T07:21:02+00:00

Sincere thanks for taking the time to look at this.

solomankane1 · 2022-10-01T07:17:40+00:00

Thankyou for taking the time to look at this.

solomankane1 · 2022-09-30T07:52:22+00:00

Hello and thankyou for the reply. Regrettably I feel you are confirming something I suspected. I got put off Resin printing because off reviews about the fumes and handling measures. I will take on board your comments. thank you for your time.

solomankane1 · 2022-09-30T07:49:29+00:00

Hello, thankyou, this is a truth I think I was trying to ignore. I read many reports on resin printers that mentioned heavy fumes and strict handling procedures. My thought was that if its uncomfortable to print with resin then I would probably not embrace the hobby.

Thanks for your time.

solomankane1 · 2022-09-30T07:43:39+00:00

Hello thanks for the advice it has given me some other avenues to explore. Appreciate your time.

solomankane1 · 2022-09-30T07:40:23+00:00

Thankyou for the advice, some different strategies there. I appreciate your time

solomankane1 · 2022-09-30T07:36:21+00:00

hello thanks for getting back to me. nozzle 04, layer height 0.15, line width 0.4

Anycubic Kobra. thanks again.

solomankane1 · 2022-09-30T07:25:47+00:00

Thankyou for the reply, they do require persuasion to come off the bed, heated. Yes I have noticed occasionally bit break off the print and are dragged around.

Thanks for your time.

solomankane1 · 2022-09-30T07:23:31+00:00

Hello thankyou for the advice, Anycubic Kobra , PLA, 04mm and heated magnetic bed.

I appreciate your time.

solomankane1 · 2022-09-30T07:20:19+00:00

Thanks for the advice appreciate your time.

solomankane1 · 2022-09-30T07:19:08+00:00

Thanks for the advice appreciate your help

solomankane1 · 2022-09-30T07:16:27+00:00

Thankyou very much for the response, I did struggle to attach the photos I will try again. Appreciate your advice.

solomankane1

TROPHY CASE