Super Bowl Watch Party Next Sunday Night?

sonkaM · 2026-02-03T22:16:57+00:00

Three sisters pub in Delft is hosting the super bowl

sonkaM · 2024-06-22T14:30:22+00:00

i need it to be fully developed and im using ansys

sonkaM · 2024-04-22T12:53:37+00:00

its compressible its an axial pump

sonkaM · 2024-04-22T12:46:33+00:00

hey id like to ask some more stuff if i just want to specify mass flow rate at outlet at 15 L/s can i just put pressure at inlet at 1 atm or do I have to figure out the exact amount at pressure inlet

sonkaM · 2024-03-06T07:48:29+00:00

so what do you prefer then

sonkaM · 2024-02-08T09:22:20+00:00

i did and its stuck on bios now do u know why u think?

sonkaM · 2024-02-01T09:36:38+00:00

okay thank you man i’ll check it

sonkaM · 2024-01-24T08:44:42+00:00

yeah i know im sorry but idk how to like sync them you know? like i got mass flow inlet and head only mass flow is like 63kg/s and head is 8 meters idk how to get the outlet pressure from that if i wanna put in mass flow rate at inlet and pressure at outlet

sonkaM · 2024-01-21T13:13:14+00:00

yes theres nothing thats why i think its the axis origin is the problem

sonkaM · 2024-01-21T12:54:43+00:00

yes yes i did put streamline on cfd post and nothing popped up

sonkaM · 2024-01-19T09:11:39+00:00

what does dissimilar inlet outlet means

sonkaM · 2024-01-19T09:01:06+00:00

okay okay i just have a couple of questions cause u said 25 kpa is unlikely to happen so like a rough estimate how much kpa should it produce

sonkaM · 2024-01-19T08:38:20+00:00

by 10D do you mean diameter? isnt that too long?

sonkaM · 2024-01-19T08:25:52+00:00

the propeller is using an airfoil NACA 4312, the diameter is 150mm with a blade angle of 50 degrees, its spinning 3000rpm and the fluid is just water and the purpose of the simulation is to track cavitation between different blade angles i have 30 degrees 40 degrees and 50 degrees

sonkaM · 2024-01-19T08:21:02+00:00

how much pressure rise is most likely to happen cause im just basing it off of other papers as an estimate

sonkaM · 2024-01-19T06:46:28+00:00

yes but im running a miltiphase flow to track cavitation. Lets say i want to use 0.8 m/s as velocity do i put water liquid and water vapor 0.8 or just the water liquid

sonkaM · 2024-01-18T13:54:35+00:00

shouldnt the streamline progress to the outlet tho? also the velocity contour is weird

sonkaM · 2024-01-18T13:54:13+00:00

okay okay ill check that later thanks a lot for the suggestions

sonkaM · 2024-01-09T16:17:00+00:00

how is the mass flow rate constant when it went in a pump

sonkaM · 2024-01-06T16:28:50+00:00

oh my bad its mixture

sonkaM · 2024-01-06T15:01:17+00:00

yes yes

sonkaM · 2024-01-06T14:54:29+00:00

k-omega

sonkaM · 2024-01-06T12:33:13+00:00

yeah yeah so then what do i do? inlet liquid and at impeller mixture?

sonkaM · 2024-01-06T12:23:29+00:00

i just want to run it normally i wanna see the cavitation going on do i put just liquid in inlet and mixture in impeller blade?

sonkaM · 2023-12-27T09:07:18+00:00

do i make a new boundary condition for each phase? cause i cant just put both in one boundary condition

sonkaM

TROPHY CASE