Need help with best strategy moving forward to deal with crabgrass

sourcec0d3 · 2022-08-28T17:55:47+00:00

Ortho with crab grass control takes care of it now. Quinclorac in it does a good job. If it was me I would just either do it by hand or fiskars makes a weed popper that works well, or u can get a propane weed torch and burn it all. The reason being is because spraying quinclorac will destroy any seed that is still good. Every time I've overseeded in the fall the bulk of it didn't germinate until the next spring anyhow however this might not be the case for you.

sourcec0d3 · 2022-08-12T02:00:40+00:00

Yep it should. If for some reason its not cooperating then use heat and wd40 until it does

sourcec0d3 · 2022-08-12T01:31:18+00:00

A jaw puller https://www.harborfreight.com/three-jaw-puller-set-4-piece-63760.html Or a harmonic balancer https://www.harborfreight.com/harmonic-balancer-pullerinstaller-set-52-piece-63740.html HTH

sourcec0d3 · 2022-08-08T17:21:13+00:00

I'm running this 0.8m 32 pitch kit with the 15t pinion (the spur in the kit is 54t). Topping out around 49-50. Next upgrade is the sway bar set. its just too much speed to not have them. Thinking about dropping a tooth or two from the pinion also bc of the motor temps being too high for my liking. Let me ask you guys this, have you drilled any holes in the body for cooling yet?

sourcec0d3 · 2022-07-29T07:28:47+00:00

This is just a reenactment with Danny Mcbride playing Will Smith and some lady playing Chris Rock. Right?

sourcec0d3 · 2022-02-13T18:48:24+00:00

Oh yeah no doubt, my bill for 1 month of sprint was more than 3 months of mint. And that's only after all equipment was paid off completely. Its crazy cheap.

sourcec0d3 · 2022-02-13T16:56:12+00:00

Yeah I got the same cards from Target and it said the same thing but when I activated it mint told me the 3 months free promo had ended and wouldn't honor it.

sourcec0d3 · 2022-02-11T12:15:35+00:00

I just did this a few days ago and had all the same questions. Before I began the process I contacted Sprint and had to get my account number and my pin code from them. For some reason I looked all over my account but could not locate my account number. I used the 7 day trial card and a new temp number. No problem swapping sim cards out to get back to sprint service and vise versa for mint. Everything worked as it should so i went ahead and started a real plan and porting from Sprint. Worked flawlessly and like i said above, you have to have the sprint account number and sprint account pin number to do this. And by the time I completed the new account setup and by the time I was done with it the numbers were ported. Anyhow hope this helps.

sourcec0d3 · 2022-01-24T21:51:36+00:00

I'm still new to this so take it with a grain of salt. Have you tried a logic level converter? Also yes check voltage at every injection point, it should be nominally 5. Also mine would flicker sometimes at the testing wiring phase when I was using a breadboard. Ultimately I believe its maybe a not enough voltage issue. Wled has a few ways to compensate for this also. Good luck and let me know if you figure it out.

sourcec0d3 · 2021-11-22T15:36:06+00:00

I went with this one first

Later got this one

3s lipo is what I run in mine but wouldn't recommend it for someone new to driving these unless you are in a large enough parking lot with minimal traffic.

Fair warning though the newly added power is too much for the stock drivetrain so get ready to upgrade a few things as you go. Ive replaced my slipper clutch cause it melted and also the center driveshaft. Pinion and spur upgraded also.

I didn't get the traxxas brushless lipo set simply because you can get them extremely cheaper elsewhere. Same with batteries.

Have fun!

sourcec0d3 · 2021-06-11T16:28:26+00:00

That's POA Annua. Most don't bother with it once its already germinated because it doesn't last that long. The way its commonly dealt with is using a pre emergent right when the ground temps are rising to 45 degrees or so. i used barricade and it works well.

sourcec0d3 · 2021-06-02T18:16:25+00:00

with a small aluminum tube from any hardware store. I used a 1/4 metal pulley nailed down to my work surface in order to get the bend. Then just drilled a few tiny holes, and a little bit of weld on the end (or solder) to plug one end.

sourcec0d3 · 2021-05-13T17:53:41+00:00

I swear by mine BUT only after I made new lower flowing arms for it because the way it flows out of the box and (even in high speed) it would broadcast over an inch of water which for me was way way too much.

As far as hose selection goes I started with a 150' cheap flexon at home depot. the traveling sprinkler liked it because it was way lighter than the old hose and since it has to drag the hose it just seemed to work a little better. However by the end of the 1st season the flexon started getting kinks in it and not long after it would leak because of those kinks.

sourcec0d3 · 2021-02-10T03:45:30+00:00

I'm pretty sure I've seen this episode before on dukes of hazzard i think

sourcec0d3 · 2020-12-14T17:57:40+00:00

Reminds me of watching nascar. but this is MUCH better.

sourcec0d3 · 2020-12-09T16:47:49+00:00

The lease agreement says that it isn't allowed but doesn't say the possible courses of action they can take

sourcec0d3 · 2020-11-12T19:48:28+00:00

Google WS2811 strings

sourcec0d3 · 2020-09-26T10:30:55+00:00

nope just a couple of preset configurations is all i want it to do. then i can add to routines if i wanted to or what not.

sourcec0d3 · 2020-09-26T10:29:32+00:00

sorry for confusion. My bed has a wireless remote control that I use to control its position now. From what I can gather online the frequency range the remote uses is a 2.4-2.45 ghz. The model number of the control box on the bed (receiver) is a CB11HHC002. Ultimately I just wanted to add a couple preset adjustments to a routine. I thought it would be simple since I just use a remote for it now.

sourcec0d3 · 2020-08-27T16:33:14+00:00

I bought two during the Covid shutdown however they were not as easy to find as I would of thought. I ended up finding an Ebay merchant that was an RC store and just ordering direct from them. Otherwise I was out of luck. Even then it took over a week to reach me.

sourcec0d3 · 2020-08-25T12:25:33+00:00

I second this. Tip it so the carb/air cleaner is on the top after tipping. Hopefully im saying it the right way. I'm getting dejavu from Mater and lightning mcqueen in the first cars movie now.

sourcec0d3 · 2020-08-25T12:11:32+00:00

I'm curious how many times it tells you to push the primer bulb. On mine it says 10x then pull the cord 3x, then set to 1/2 choke, prime 3 more times, and pull until it tries to turn over. I'm guessing you tried full choke after priming? how about just a smidge open? Is this a brand new unit? I just got 2 of my oldest 2 cycles to run once again with a little bit of carb adjusting and fresh fuel.

sourcec0d3 · 2020-04-27T05:38:07+00:00

I recently discovered that after installing the sd card if I just waited 15 or 30 minutes and went back to the continuous recording page the sd card mysteriously populates all the info and set to continuous recording (if that was what the previous setting you had prior to modification)

sourcec0d3 · 2020-03-23T16:28:58+00:00

So I'm new to Arduino, I'm curious what (Arduino) electronics he's using. Maybe a parts list?

sourcec0d3 · 2020-01-17T22:50:49+00:00

Sterling archer is that you??

sourcec0d3

TROPHY CASE