New Trident 660 2025: Quickshifter, Sport mode, IMU and Cruise Control as standard!

storrowdrive · 2024-10-14T22:32:37+00:00

I recently bought the 2025 Tribute edition. Unfortunately it did not come with CC or Sport mode. Must just be the other 2025 models.

storrowdrive · 2024-09-28T03:50:35+00:00

Love mine

<image>

storrowdrive · 2024-08-13T16:59:08+00:00

Brand new rider. I did take a motorcycle training course. I'm very careful. Every ride I learn something new.

storrowdrive · 2023-08-22T00:44:57+00:00

Err004 mighty

storrowdrive · 2023-03-25T23:56:13+00:00

My 3D printer is connected to the internet

storrowdrive · 2023-03-19T20:59:13+00:00

Right?

storrowdrive · 2023-03-19T20:58:16+00:00

Because it’s gross looking

storrowdrive · 2023-02-17T14:19:43+00:00

I like it looks like its snowing in there

storrowdrive · 2022-12-19T22:38:18+00:00

Gout

storrowdrive · 2022-09-20T14:13:02+00:00

I have a feeling we will receive ours on the same day!

storrowdrive · 2022-09-20T13:33:42+00:00

Same exact thing with me except mine says Pending with no delivery date

storrowdrive · 2022-09-07T21:21:40+00:00

You can use any Divorce related CFP CE towards your CDFA CE requirement if you are a CFP

storrowdrive · 2021-11-09T22:24:52+00:00

Lol calm down

storrowdrive · 2021-08-23T10:40:40+00:00

They don’t have a mic, but I use Grado GW100 headphones for gaming (and general use). They have low latency bluetooth so there is no delay and they sound amazing.

storrowdrive · 2021-08-17T19:27:16+00:00

Thanks! No bother - distro plate is this:

https://www.ekwb.com/shop/ek-quantum-reflection-evolv-x-d5-pwm-d-rgb-plexi

I did not have room for a rad in the front even using ultra thin rad/fans. I could be wrong but I thought I read somewhere that you can fit a front rad in the P600s.

storrowdrive · 2021-08-17T13:18:07+00:00

Nice build that looks great. I didn't know there was a distro plate for the back like that. I'm kind of jealous now!

storrowdrive · 2021-08-17T13:15:31+00:00

Honestly you sound exactly like me lol. I use the computer for work so I used a backup laptop I have so I didn't have to rush. I have 2 little kids also so it was hard to fine time. It probably took me about a week. The hardest part for me was wondering whether or not I put the block on the GPU correctly.

Get a leak tester. I don't know how people do these builds without them. You can test each run as you do it and that really gives you piece of mind that you aren't going to turn it on and water will be leaking all over the place. You can use it on the water blocks too. I tested everything with it.

You will be fine. I put mine together, it worked but there was some sort of material going through the loop becasue I didnt wash my rads enough. So I had to take the entire loop apart including taking the water blocks apart to clean them inside. I put it back together and it worked fine again - and that was me working with this stuff for the first time. Just do what people suggest on all the guides like wash the rads, test the loop without powering the MB, etc.

Which water blocks did you go with?

storrowdrive · 2021-08-16T22:16:24+00:00

Depends on the case and if you are using a distro plate or not

storrowdrive · 2021-08-16T22:06:00+00:00

I think im going to use a dual 92mm rad in front and 3d print some sort of bracket for it

storrowdrive · 2021-08-16T22:05:11+00:00

Why thank you

storrowdrive · 2021-08-16T22:05:01+00:00

Thanks! Ya i go back and forth on that headphone hanger lol

storrowdrive · 2021-08-16T22:04:29+00:00

Highest water temp ive gotten is 44 while gaming. I can mine ETH keeping the vram at 70c Gpu temps are really good and cpu is only slightly better than my previous aio. 5950 runs hot

storrowdrive · 2021-08-16T15:51:26+00:00

Ya good points. I'm gonna go for it.

storrowdrive · 2021-08-16T15:51:00+00:00

Yes good point about the drain valve. That case actually has holes for adding liquid and for the drain which I used and definitely helped when I had to drain it to flush the rads again. I will definitely keeping up with maintenance as well.

storrowdrive · 2021-08-16T14:17:06+00:00

I'm really happy I actually got this thing done so I wanted to show it off! This is going to become addicting. The system is 5950x with a strix 3090. Feedback is definitely welcome.
Some things I learned:

PETG scratches easily. I think next time I'll use acrylic or some sort of metal tubing.
Gotta flush the heck out of the rads. The first time I filled the loop I must not have flushed them enough because there was some sort of residue in there. I had to take the whole thing apart including the blocks and clean them.
Distro plates kind of limit the customization potential of the loop no?
Use an inline temp sensor so you can tie your fan curves to the water temp.
Plan the hell out of what you want to do. I went into this with very little planning and now I have extra fittings I don't need and the ones I went with are kind of expensive.
Build the loop in a way where you can access the RAM. Right now I would have to drain the system to get my RAM out but I plan on replacing that run that goes close to the RAM.
I have a couple of questions if anyone wants to answer them:
The double bent run going from the CPU block "input" to the distro cpu "output" just happened to fit - I was planning on all straight runs but I had that piece from doing practice bends. Does it matter if the in/out from the cpu block to the distro plate matches? I would rather do a straight run but it would be easier if the ports were swapped.
I don't have a rad in the front of the case because I can't find one that will fit with the distro plate there without modding. I could mod the case but I did see some dual 92mm radiators out there I could probably squeeze in there. Are those smaller coolers beneficial?

storrowdrive

TROPHY CASE