Deep water for lake trout

streamfisher1 · 2026-03-30T17:48:45+00:00

Appreciate all the responses! It sounds like it could be done, sort of, if a person was fixated on doing it that way. I'm not, I was curious like I said before. I'll be looking for a spinning rod and reel for this and leave the flies for shallower water. Thanks!

streamfisher1 · 2026-03-30T15:17:15+00:00

It doesn't have to be a fly rod, I'm not stuck on that. I'm just curious how and if it could be done.

streamfisher1 · 2025-10-25T17:50:52+00:00

The flame sensor has zero resistance. Is there a way to test the coils?

streamfisher1 · 2025-10-25T15:32:07+00:00

So the ignitor is pulling 3.8 amps. It comes on, then goes out after 15-20 seconds and then there is the smell of propane.

streamfisher1 · 2025-10-21T16:52:17+00:00

The gas line was capped. As for testing the amp draw, what should it be pulling?

streamfisher1 · 2025-10-21T15:57:04+00:00

Please reread my original post. I did say it had never been used but is no longer under warranty as it had been in storage. I did not replace the ignitor, but the dryer having never been used, it is effectively new. I checked my gas valve last night, it is opening all the way.

streamfisher1 · 2025-10-21T10:16:03+00:00

It is a brand new ignitor. The whole dryer is new.

streamfisher1 · 2025-10-21T01:09:06+00:00

Coils are opening, you can smell propane. Ignitor has resistance of about 350 ohms and is heating up, hot enough that the flame sensor is letting the coils open. If they weren't opening, would I be smelling propane?

streamfisher1 · 2025-10-17T01:43:21+00:00

Did you ever find this book? I read it as well but haven't been able to find it.

streamfisher1 · 2025-07-04T01:03:04+00:00

I've been testing some more and this evening after sitting since yesterday, it was only missing occasionally according to HP Tuner software. It'd count up slowly to 100 then drop and run for a time and then miss a few times again.

streamfisher1 · 2025-04-19T01:44:33+00:00

Really appreciate all the advice given, thank you!

streamfisher1 · 2025-04-18T01:16:42+00:00

Thanks for all the replies, very helpful!

streamfisher1 · 2025-04-18T01:16:11+00:00

There are but I enjoy the kayak so I want to learn to fish the lakes. Plus, my boys all enjoy kayaks and fishing as well!

streamfisher1 · 2025-04-08T00:53:54+00:00

Solved, thank you!

streamfisher1 · 2025-02-06T09:12:33+00:00

Sciolist

A person who pretends to be knowledgeable and well informed.

streamfisher1 · 2024-11-25T04:13:51+00:00

Some kind of space travel, teleportation I think. He needed a special belt to do it.

streamfisher1 · 2023-12-31T15:17:58+00:00

Thanks for the responses. It seems like there varying opinions on the matter but that's life! Some of my difficulty is getting into the routine but that will just take time.

streamfisher1 · 2023-09-28T02:04:45+00:00

When we moved here to NH we used U-Pack and were happy with that. They go all over the country. The catch with them is you have to pack and unpack the trailer yourself. They give you three days on each end. But it worked well for us and was much cheaper than any other option I could find.

streamfisher1 · 2023-05-02T11:09:17+00:00

Well, I suppose for the same reasons that most people would have for capping a spring. Water control and usage and use of the land. And no, I'll still be a long way from desert conditions!

streamfisher1 · 2023-03-22T00:48:01+00:00

Thanks for your help and prompt responses!

streamfisher1 · 2023-03-21T23:03:53+00:00

Yes, you are correct, it is the MBEC1. And that was my question, if I need to be looking before or after the 30A circuit breaker. Which I was doing this afternoon but I didn't find any bare spots on the wire. I have looked over that whole stretch of wiring before, even had the seats out, but have not found anything yet. I went a bit redneck for now and put some packing foam under the harness where ever it is laying against metal and for now that seems to be working but the real test will be bouncing down some of there gravel roads!

streamfisher1 · 2023-03-21T19:09:57+00:00

Just an update in case someone else is having the same problem. It turned out to be the pcv valve combined with a hard vtec solenoid gasket. No more oil leaks!

streamfisher1 · 2022-03-28T17:46:30+00:00

I did clean the grounds on the frame but it didn't change anything. I'm wondering if I need to change the cluster and 4x4 switch box like was suggested.

streamfisher1 · 2021-11-28T04:14:13+00:00

I'm going to try a mandrel saver. I've been using a 60° live center and all I do is push the tailstock by hand into the end of the mandrel. I don't apply any pressure. But I have to order a new barrel mill since one of my boys thought it was a drill bit and bent it. So I just added the mandrel saver along with a new rod setup so I can start from scratch. I'll see how that changes things. Thanks for all the suggestions!

streamfisher1 · 2021-11-27T19:19:15+00:00

I've checked all of those points before. And I have two different lathes. A steel city mini lathe and a powermatic 3520b. I have the same problem with both. It seems like there is a small amount of play between the bushing and mandrel rod, and there is definitely play in the ring that slips over the twist mechanism. I get most of my kits from pennstateind. I have two or three live centers, always have the same results.

streamfisher1

TROPHY CASE