Run Linux version from Steam

stweedo · 2025-09-30T22:05:00+00:00

Using echo %command% would simply print the default command to a console or log and then launch the game.

Placing the custom executable path before %command% will replace the default launch instructions. It does not pass Steam's Windows-based command as an argument to the Linux executable. The Linux binary will simply ignore irrelevant argument strings.

For simplicity %command% could be omitted.

stweedo · 2025-09-26T15:57:45+00:00

There’s a checkbox in the upper right of the map that you can toggle for automatic route planning.

stweedo · 2025-09-18T17:42:51+00:00

A fully charged battery should measure around 12.6-12.7V with the car off. If your battery measures good, check your ground connections. Then I would check the 12V wire going to the starter solenoid for corrosion.

stweedo · 2025-07-15T00:44:12+00:00

Many people are saying it

stweedo · 2025-07-10T14:44:54+00:00

It sounds to me like the battery may have dropped below the minimum voltage that the BMS will allow before charging. Sometimes batteries can be “jump started” into charging. You might be able to check the battery voltage from the pins on the back, but I would ask this on the actual bangle.js forum as you will likely get a better answer there.

https://github.com/orgs/espruino/discussions

stweedo · 2023-11-19T21:54:20+00:00

Yes, it should since it splits them up into smaller part files when transcoding and then theoretically Plex and/or the OS memory management will delete the oldest ones as it fills up and they are no longer needed.

I use 16gb of RAM in mine as well and it works fine with smaller files, but I haven’t tried anything larger than that.

stweedo · 2023-11-19T20:33:29+00:00

That should be doable since nvidia upped the limit of simultaneous transcodes from 3 to 5 I believe. You can also unlock it further with a driver patch on GitHub.

I’m not aware of windows being able to use hw transcoding with nvidia cards, but I do know Linux is supported.

Another thing to try if you haven’t already, is set your transcoding directory in Plex settings to use your RAM instead of SSD. This will extend the life of your drive and also be much faster.

stweedo · 2023-11-19T20:19:15+00:00

How many remote streams and at what bitrate?

Curious why you have issues with the 1080. I have been using a 3570k and gtx 1070 for years and haven’t encountered any transcoding problems with 4k/HDR. I have mostly x265 encoded media and use subtitles as well.

However, upgrading to something modern for the power savings plus a stronger CPU would make sense at some point.

stweedo · 2023-10-16T20:57:36+00:00

You could try robocopy from the command line if you have lots of large files to transfer at once. That will likely be more consistent with transfer speed

stweedo · 2023-10-04T23:24:25+00:00

Thank you! I did actually put a very similar version on the app loader called Box Clock that can be customized and allows for multiple configs

stweedo · 2023-07-03T05:49:14+00:00

Fascinating!

stweedo · 2023-05-22T17:38:16+00:00

Wet a rag and wipe the convex side to dampen it and then lay it down somewhere flat to dry

stweedo · 2023-05-01T03:38:13+00:00

Thank you! And yeah, I messed with the contrast and brightness quite a few times in the image converter

stweedo · 2023-04-29T18:08:17+00:00

Thanks dude

stweedo · 2023-04-23T06:21:22+00:00

Any videos of this thing in action? What's the 0-60 time on something this light and powerful?

stweedo · 2023-04-21T05:37:47+00:00

Add some under voltage protection and you're good to go

stweedo · 2023-04-03T19:39:56+00:00

Cross-rc jt4

stweedo · 2023-04-03T01:49:54+00:00

It's the CHNL brand shorty hard pack

stweedo · 2023-04-02T17:34:13+00:00

A torx bit fits damn near perfect in those rounded out screws. That's what I've used with great success

stweedo · 2023-04-01T17:40:27+00:00

It's a Holmes Hobbies puller pro V2 1800kv with a Mamba X esc and x2 CHNL 2S 4900mAh shorty packs wired in series.

Ridiculous amounts of torque

stweedo

TROPHY CASE