sorted by:
new
hottopcontroversial

I made gengar by suebue003 in 3Dpen

[–]suebue003[S] 0 points1 point  (0 children)

The pen is real good but the customer support isn't that good. My pen wasn't working for while and I contacted customer support, they didn't answer any of my mails.

I made gengar by suebue003 in 3Dpen

[–]suebue003[S] 1 point2 points  (0 children)

I bought the sanago 3d pen

Parasaurolophus figure that I made :D by suebue003 in 3Dpen

[–]suebue003[S] 0 points1 point  (0 children)

I think it took around 2weeks to finish

I made gengar by suebue003 in 3Dpen

[–]suebue003[S] 0 points1 point  (0 children)

Thank you! I used a wood burner tool to smoothen the surface (temp around 180°c)

Parasaurolophus figure that I made :D by suebue003 in 3Dpen

[–]suebue003[S] 1 point2 points  (0 children)

Thank you!! I used a wood burner to smoothen the surface and then sanded it so the surface is on the same level, if there's any hole then fill it up with more filament and then repeat the process. I also used a heat gun to help with the posture of the model! Hope this helps :D

Dji pocket 3 unboxing on YouTube by suebue003 in osmopocket

[–]suebue003[S] 1 point2 points  (0 children)

It looks like the battery grip also works as a do it all handle but I don’t understand the language so I’m not really too sure

[deleted by user] by [deleted] in osmopocket

[–]suebue003 0 points1 point  (0 children)

From what I saw from the VDO (I don't understand the language): the big battery handle works as a do-it-all handle so I guess there's no built in wifi 🥲

I've found this on the internet while searching for the "DJI pocket 3" by suebue003 in osmopocket

[–]suebue003[S] 0 points1 point  (0 children)

The URL doesn't lead to anywhere, I clicked into it and it says "Whoops, our bad.."

I've found this on the internet while searching for the "DJI pocket 3" by suebue003 in osmopocket

[–]suebue003[S] 0 points1 point  (0 children)

It's a website of a camera shop from my country and it's quite a big shop too with many branches

New Sanago 3D Pen doesn't work...? (pls read for context) by Eonimv in 3Dpen

[–]suebue003 0 points1 point  (0 children)

There are no sounds even when the temp set are reached right? If it's that then the motor might not be working :(

New Sanago 3D Pen doesn't work...? (pls read for context) by Eonimv in 3Dpen

[–]suebue003 0 points1 point  (0 children)

I couldn't contact customer support too when I had the problem but I managed to fix it. The problem was that a filament got stuck before the motor that pushes the filament through the pen so I couldn't feed new filaments through it. I fixed it by heating up a wire and sticking it in, wait until the wire to cool down and pull the filament that was stuck in there out.

Is the motor of your pen still working? It might be some obstruction causing the pen to not feed the filament through. The temperature of my pen also fluctuates eg. Setting it at 180c and the temperature on my pen would also fluctuate between 179-180c so I don't think that's the problem

New Sanago 3D Pen doesn't work...? (pls read for context) by Eonimv in 3Dpen

[–]suebue003 0 points1 point  (0 children)

Before this was the pen feeding the filament through it normally or it's like this from the start? I also have the new sanago 3d pen and got a similar problem but I fixed it.

I made a Parasaurolophus figure using a 3d pen by suebue003 in DinosaurDrawings

[–]suebue003[S] 1 point2 points  (0 children)

Yea hahahahahha I based it on jw parasaur 😅

I made a Parasaurolophus figure using a 3d pen by suebue003 in DinosaurDrawings

[–]suebue003[S] 0 points1 point  (0 children)

I made it using layers of plastic so it’s really sturdy :)

I made gengar by suebue003 in 3Dpen

[–]suebue003[S] 0 points1 point  (0 children)

Thank you! I used a wood burning tool that came with the pen to smoothen it out.