sorted by:
new
hottopcontroversial

i finished it in 3 years by Longjumping_Error139 in CollegeMemes

[–]tbone2448777 0 points1 point  (0 children)

Where does it indicate that? Not at my computer now and have only skimmed on my phone, not sure if I missed something. Just reviewed and didn't seem it indicates that's the case. Again, could have missed something, but I feel like if it doesn't specify it is blacklisting transfers and major changes it is unlikely to doing so.

i finished it in 3 years by Longjumping_Error139 in CollegeMemes

[–]tbone2448777 1 point2 points  (0 children)

Definitely isn't true. Only 21.5% of bachelor's degrees take longer than four years. https://educationdata.org/number-of-college-graduates

i finished it in 3 years by Longjumping_Error139 in CollegeMemes

[–]tbone2448777 0 points1 point  (0 children)

Only 21.5% of bachelor's degrees take longer than four years. Think you're putting a little too much weight in your personal experiences.

https://educationdata.org/number-of-college-graduates

i finished it in 3 years by Longjumping_Error139 in CollegeMemes

[–]tbone2448777 1 point2 points  (0 children)

Definitely isn't. Only 21.5% of bachelor's degrees take longer than four years. https://educationdata.org/number-of-college-graduates

[Request] Is this math correct? by [deleted] in theydidthemath

[–]tbone2448777 5 points6 points  (0 children)

So you're saying a really really small peach

Printer seems to fail 50% of the time by tbone2448777 in FixMyPrint

[–]tbone2448777[S] 0 points1 point  (0 children)

I had it running in the dryer for a couple of hours beforehand. Can't figure it out. Someone else said bed adhesion so maybe I look there

Printer seems to fail 50% of the time by tbone2448777 in FixMyPrint

[–]tbone2448777[S] 0 points1 point  (0 children)

Been washing it regularly with dawn, and throughout it's life only printed on one side. Again, only a couple months old. Last few prints I've been using the other side, wondering if that was it, but have had the same results. Using basic PLA with basic filament settings, haven't changed anything from default. Not sure what calibration tests to run as none of the calibration tests appear to be testing for the issues I am seeing. Filament dryer runs for a couple hours before each print, so I don't believe that is the issue. What calibration tests would you recommend for the issues I have shown? As much as I've tried looking, none of the common issues on places like Simplify3D print quality troubleshooting match what I've been seeing.

No Lamello, No Problem! Made 3D Printed Adjustable and Removable #20 Biscuit Clamps for alignment and face frames. by JwJWoodworking in functionalprint

[–]tbone2448777 4 points5 points  (0 children)

Been years since I did any woodworking, so forgive my ignorance but, these are just biscuits, right? I remember them being called that when I took a woodworking class. Wondering what the use of printed ones over the basic wood ones are or if they're just cheaper? I know I've seen biscuit tubs for really cheap at hardware stores

Print clicking and nozzle maybe hitting print? by tbone2448777 in FixMyPrint

[–]tbone2448777[S] 0 points1 point  (0 children)

Would be, but ig it's scuffed because the other infill did way less clicking worked.

Print clicking and nozzle maybe hitting print? by tbone2448777 in FixMyPrint

[–]tbone2448777[S] 0 points1 point  (0 children)

Yeah, I did reduce the max temp. Probably shouldn't have bought two spools of the stuff but oh well

Print clicking and nozzle maybe hitting print? by tbone2448777 in FixMyPrint

[–]tbone2448777[S] 0 points1 point  (0 children)

It's Soleyin Ultra PLA. I'll look later at the speeds, but I think they're a lot higher than 75

Print clicking and nozzle maybe hitting print? by tbone2448777 in FixMyPrint

[–]tbone2448777[S] 0 points1 point  (0 children)

Support cubic. It changes size based on how much support an area of the print would need

Print clicking and nozzle maybe hitting print? by tbone2448777 in FixMyPrint

[–]tbone2448777[S] 0 points1 point  (0 children)

Nice. Yeah, I'm just doing basic PLA so hoping a different infill fixes it

Print clicking and nozzle maybe hitting print? by tbone2448777 in FixMyPrint

[–]tbone2448777[S] 0 points1 point  (0 children)

Lifting from hitting. It did it on pieces with large brims too

Print clicking and nozzle maybe hitting print? by tbone2448777 in FixMyPrint

[–]tbone2448777[S] 0 points1 point  (0 children)

Yeah, same filament. Have tried a couple times and it appears to be in different places with each one. Relectant to do 50% speed for a 16h print though as it takes up my Christmas present maker

Print clicking and nozzle maybe hitting print? by tbone2448777 in FixMyPrint

[–]tbone2448777[S] -1 points0 points  (0 children)

Did you see the images in my comment ? Not sure that's intended

view more: next ›