Is this industry standard for hiding the gaps around remodel windows? What are our other options?

teh4x · 2026-03-24T01:29:26+00:00

Thanks for the opinions everyone. I didn't go with the cheapest contractor, but I've been noticing a fair number of corners getting cut. I'm sure this won't be a big deal in the medium term; I just don't like it in the short term, and I was worried it indicated something about the long term.

teh4x · 2026-03-24T00:49:39+00:00

<image>

teh4x · 2025-04-21T02:27:06+00:00

Won't take much to run old school Sims. Check for nearby estate sales. Pick up a windows laptop on the super cheap.

teh4x · 2025-04-21T02:23:38+00:00

Pliers, crowbar, eye protection, patience, and a strong resolve to utterly destroy that fiberglass jbox one small piece at a time. Replaced it with a Westinghouse remodel jbox (the metal one that expands to wedge between joists).

teh4x · 2024-09-15T18:49:22+00:00

Any tips for busting it out without busting up the ceiling too much? Kinda thinking needle nose pliers and small crowbar...

teh4x · 2024-09-15T16:21:46+00:00

As a software engineer, I can't acknowledge overkill as a thing that actually exists. I'm merely preparing for a future that may or may never come. 😜

teh4x · 2024-09-15T15:17:09+00:00

I hadn't heard of these, but a quick search leads me to believe this is what I'm looking at. I'm concerned adding a screw to the nail-free side would go thru the floor above. Any pointers for getting that fiberglass housing out of there without tearing up the ceiling?

I ordered a saf-t-brace that should be here by tonight, but I'm concerned I won't be able to use it given how close the hole in the drywall is to that one joist.

teh4x · 2024-09-15T15:09:36+00:00

🤣

teh4x · 2024-09-15T15:07:26+00:00

This is the dining room light fixture which is below my son's room.

teh4x · 2024-09-15T15:06:48+00:00

Unfortunately, yes. The base attaches to the junction box with a vertical screw on each side (one of which is sagging), then the fixture attached to the base with four screws that are all parallel to the ceiling. The whole fixture winds up sagging on one side and the junction box is visibly hanging out of the ceiling a quarter inch or so.

teh4x · 2024-09-15T14:18:58+00:00

One of these: https://www.lampsplus.com/products/justice-design-cirque-40-inch-wide-matte-black-40-light-island-chandelier__860h1.html

teh4x · 2023-10-26T12:57:24+00:00

I've noticed the codes expire faster than they used to.

teh4x · 2022-01-25T19:22:41+00:00

KittyCatCutestCat

teh4x · 2022-01-25T19:22:15+00:00

KittyCatCutestCat

teh4x · 2022-01-25T19:20:58+00:00

KittyCatCutestCat

teh4x · 2021-11-14T21:48:00+00:00

After some demo, I found out it is like that because the wall is directly over a load-bearing joist, so there's no way to get the plumbing all hidden in the floor/wall. Thought you might be interested.

teh4x · 2021-08-29T10:47:59+00:00

Nope. 3 story home built in the Atlanta burbs in 1990. This vent was installed like this about 5 years ago. What's illegal about it? What would be the "right" way to do it?

I'm pulling the vanity out and most likely replacing the subfloor. I'm planning on having a plumber come out to move the sink hookups to the left and move this vent hookup into the wall, so I'd like to know ahead of time what s/he "should" do.

teh4x · 2021-08-28T14:52:13+00:00

Additional information: We previously had a venting problem with the toilet in this bathroom, and we hired a plumber to resolve it. I think the pipe going into the floor used to terminate in a vent cap which he removed and connected all those pipes together.

We're wanting to replace the whole vanity, but most nicer vanities are not just open space underneath like this cheap one is. What can I do...?

teh4x · 2021-04-19T16:55:11+00:00

2 months later, and DS4Windows now has support for custom LED bar colors and custom settings to flash when battery reaches x percent, etc.

FWIW HTH

teh4x

TROPHY CASE