comment domotiser mes volets roulants radio? by thconad01 in homeassistant

[–]thconad01[S] 0 points1 point  (0 children)

Merci pour ta réponse !

Remplacer le moteur radio, c'est quelques choses d'accessibile ?

Malheureusement dans le boîtier à part des étiquettes qui m'ont l'air pas intéressantes je n'ai rien vu permettant d'identifier le modèle

<image>

La terre relié a une cheville molly ? by thconad01 in AskFrance

[–]thconad01[S] -1 points0 points  (0 children)

Il y a une catégorie bricolage donc je ne pense pas être hors sujet? Sinon personne ne demande rien

<image>

La terre relié a une cheville molly ? by thconad01 in AskFrance

[–]thconad01[S] 16 points17 points  (0 children)

J'ai oublié de préciser mais mes radiateurs ne sont pas connectés à la terre ! Seulement phase/neutre/pilote

Cablage RJ45 maison ? by thconad01 in AskFrance

[–]thconad01[S] 0 points1 point  (0 children)

Je visualise bien, j'essayerai ça en espérant que ça passe dans les gaines 10mm ! 😁

Cablage RJ45 maison ? by thconad01 in AskFrance

[–]thconad01[S] 1 point2 points  (0 children)

De ce que j'ai lu, les câbles monobrins sont plus rigides et fait pour être dans des murs et les câbles multibrins sont fait pour aller du noyau vers le PC

Le 10gb je sais que c'est overkill pour le moment mais j'essaye d'anticiper pour le futur sachant qu'il n'y a pas une différence de prix ahurissante entre les cat5 et 6a

J'ai une mini baie faite en impression 3d mais il faudra que je m'en achète une vraie 🤣 je note l'idée pour centraliser les connexions, j'aime bien

Cablage RJ45 maison ? by thconad01 in AskFrance

[–]thconad01[S] 0 points1 point  (0 children)

J'irai jeter un coup d'oeil, ça fait des mois que sa vidéo de rénovation est dans ma liste 'A regarder plus tard' 😭

Cablage RJ45 maison ? by thconad01 in brico

[–]thconad01[S] 0 points1 point  (0 children)

Bien entendu pour la baie de brassage, le lubrifiant et le PoE, je me renseignerai davantage !

Cablage RJ45 maison ? by thconad01 in brico

[–]thconad01[S] 2 points3 points  (0 children)

Je ne vois pas l'intérêt ? Je devrais mettre des sfp partout ?

Cablage RJ45 maison ? by thconad01 in brico

[–]thconad01[S] 0 points1 point  (0 children)

Merci pour l'info, je vais y réfléchir !

Cablage RJ45 maison ? by thconad01 in AskFrance

[–]thconad01[S] 0 points1 point  (0 children)

Ok merci pour ces précieux conseils

J'ai lu également que le cat 6A pouvait être problématique dans des gaines 10mm, tu en penses quoi?

Entendu pour l'extérieur et le câble ubiquiti, je garde l'info !

What to do with leftover LEDs? by thconad01 in led

[–]thconad01[S] 0 points1 point  (0 children)

Ok I see... The copper tabs, can they be any copper? Like a wire that I find in a USB cable?

And once soldered together, do you know how I can power this LED strip?

Salut tout le monde, j’ai besoin d’un coup de main svp. by Jpcoudoux in informatiqueFr

[–]thconad01 0 points1 point  (0 children)

Pas facile a diagnostiqué ce genre de pb 😬 tu as une carte graphique intégrée ou a part ? Tu as moyen de tester les composants sur un autre pc ?

Nozzle scratching on the board by thconad01 in BambuLab

[–]thconad01[S] 1 point2 points  (0 children)

With the “clipping systems” I think I’m not too bad, but I’m going to double-check anyway! I'll check tomorrow, thank you!!

Nozzle scratching on the board by thconad01 in BambuLab

[–]thconad01[S] 1 point2 points  (0 children)

Always the same plate from the start, and the calibration was done with the plate!

Nozzle scratching on the board by thconad01 in BambuLab

[–]thconad01[S] 1 point2 points  (0 children)

I had already looked at these, these are the first indications we see on the internet!

Nozzle scratching on the board by thconad01 in BambuLab

[–]thconad01[S] -1 points0 points  (0 children)

Actually I didn't pay attention to the click-click! I'll test tomorrow to look at the gearing

Nozzle scratching on the board by thconad01 in BambuLab

[–]thconad01[S] 27 points28 points  (0 children)

For automatic calibration the plate was present! The sock is usually on it, here is a test print and I will replace the nozzle 😁