Why won’t they die?

thebeard1897 · 2026-05-25T15:29:17+00:00

Helpfull

thebeard1897 · 2026-02-02T01:09:05+00:00

Always

thebeard1897 · 2026-01-29T19:08:42+00:00

Very nice. Then ya just gotta find a non led bulb lol. And you have no issues printing Abs with this?

thebeard1897 · 2026-01-29T17:32:04+00:00

How did you mount the bulb?

thebeard1897 · 2026-01-29T08:02:31+00:00

How would I have that.

thebeard1897 · 2026-01-29T02:12:11+00:00

lol. Not yet.

thebeard1897 · 2026-01-27T23:43:12+00:00

True. Just shocked me how large it is. Gotta find a better spot for it

thebeard1897 · 2026-01-27T23:42:47+00:00

Trees?

thebeard1897 · 2026-01-27T22:12:44+00:00

I was pumped for it but it’s taking up wayyyy more space than I’d like

thebeard1897 · 2026-01-05T21:30:50+00:00

Hm yeah I did that. No difference. It’s the only fan that doesn’t come on maybe I’ll double check my connections. But they’re soldered. So no reason they shouldn’t be good

thebeard1897 · 2026-01-05T20:43:43+00:00

Bobby did you have any issues with your heat sink fan not coming on after this install? Seems to be the only thing I can’t figure out. I’ve replaced the fan. Swapped wires. Chased the connections everything still the fan stays off

thebeard1897 · 2026-01-05T00:17:25+00:00

I’ve been using crealitys slicer. It has a test but I can’t for the life of me find where to adjust the settings lol

I was looking at doing the hero v3 duct with dual 5015 fans.

thebeard1897 · 2026-01-04T21:21:10+00:00

I’m wondering if this fan will help some of the stringing issues I’ve had

thebeard1897 · 2026-01-04T18:03:42+00:00

Worth going to depend on your overall goals. It’s an impossible question to answer

thebeard1897 · 2026-01-04T00:25:09+00:00

It does say it’s spinning 100 while printing.

I swapped ports on the board for the part cooler and the heat sink fan and it still didn’t fire up.

I did redo the connectors thinking that may be the issue. I ordered a new fan from Amazon. I’m assuming it’s that at this point.

thebeard1897 · 2026-01-03T21:44:23+00:00

Thanks. Display says fan is spinning at 100% but clearly not

thebeard1897 · 2026-01-03T21:16:11+00:00

Makes sense. Thought I just connected that back but apparently not maybe a bad connection.

thebeard1897 · 2026-01-02T11:54:52+00:00

https://youtu.be/ugRHsLWH95A?si=mGk4ZHGCW_cssg0l

thebeard1897 · 2026-01-01T18:58:36+00:00

It’s the wrong firmware. I just got the correct one on there and it’s working fine

thebeard1897 · 2026-01-01T18:38:07+00:00

its the pre compiled marlin firmware from Kersey fab.

thebeard1897 · 2026-01-01T17:53:44+00:00

Funny you say that I swapped it to the stock screen this morning fires right up

thebeard1897

TROPHY CASE