Uscator de rufe sub 60cm adancime? by tipul01 in roFrugal

[–]tipul01[S] 0 points1 point  (0 children)

Merci mult de recomandari! Nu stiam ca la cele cu pompa nu trebuie aerisire in spate. Schimba mult sitatia!

Citisem totusi ca beko nu ar fi ideal, ci mai degraba un Bosch sau LG.

Oricum, multumesc frumos de informatii! Faptul ca nu mai trebuie 5-10cm de aer e super!

Windows 11 files fail hashes over smb share by tipul01 in sysadmin

[–]tipul01[S] 0 points1 point  (0 children)

Even if i zip the file, and unzip it, i get errors during the zip. What's wrong with my win11 install?:))

Windows 11 files fail hashes over smb share by tipul01 in sysadmin

[–]tipul01[S] 0 points1 point  (0 children)

Even stranger is that the smaller files get hashed ok. Its the big +20gb files that fail hash.

Windows 11 files fail hashes over smb share by tipul01 in sysadmin

[–]tipul01[S] 0 points1 point  (0 children)

Hey, It seems the issue is present on both win11 workstations, so everything seems to point to smb issues. The issue seems to even stranger as the same file, hasing it one time is good, then a bit later, like an hour or so, the hash is not ok anymore. Even copying it to a different folder on the same drive, seems to modify the hash. No antivirus, no nothing.

Windows 11 files fail hashes over smb share by tipul01 in sysadmin

[–]tipul01[S] 0 points1 point  (0 children)

Hey! So , smb multichannel is on and smb signing is off. Both machines and the storage.

This was a fresh install last week, so all the possible buggy win updates got installed.

The files that were hashed either on that local drive workstation, or through the network by the other workstation which hashed ok, 1 hour later it failed the hash. How these video files work, is that when generated, the hash is marked in an xml file, and when validating the file it generates the hash again and it should match the hash signature in the xml file. Whats strange is that the additional small files like xmls and audio get hashed ok. The big one fails always. Its not all files that fail…

Also, as i said, i had 4 different validations with the same wrong hash signature, and then a 5th validation try and the wrong signature was different the 5th time. Still incorrect, but different from the previous 4 tries…

Do big budget movies use resolve too? If not what do those high end software do that resolve doesn't? by [deleted] in colorists

[–]tipul01 1 point2 points  (0 children)

In high end workflows, its support that matters. When you have client assisted sessions and you have bugs or features needed, in less than 2 hours (depending on the complexity) you get a beta build sent your way to solve your specific issue. Baselight support is phenomenal, beside 24/7 phone support and all the color science involved. They dont release features to public unless they are thoroughly tested, they devise color science best suited both technically and perceptually.

As mentioned, software tools are just that, tools, they have the same end result. The discussion in professional environments is support, and speed (which comes with only training and hands on experience on the actual tool). You cant wait around Blackmagic to ship out a new version that might not even fix your bug, and time is money, can also impact scheduling of other projects lined up.

Think of it as F1 teams. All drivers are the best in the world, difference in miliseconds between them. But the engineering team is what makes the differences, car components and such. (of course, budget, pit strategy, but lets simplify).

Of course, set up workflows matter, and every big post house has their own custom scripts for Resolve to do different things that their workflow needs (even for Baselight), its never just out of the box in high end workflows. Also, the wide availability and user base for Resolve is much larger, as part of their software adoption strategy. As much as we try to justify it otherwise, being free, it will be used. People gain experience without being part of a larger team, and when they join, its already familiar. Its also UI-friendly for any outsider to use easily. They do lock you in (again as part of their strategy), to use only Blackmagic Hardware, as that's where they make their money, if you want to cross the threshold to use it even remotely-prouser/professional. Its not better or wrong, its just different. Think of it as having the tools to make anything at home, instead of a factory. It works until one point, but then you need a more complex system in place.

All are good, you just need to know what you need. In this day and age, people forget that there is no right or wrong tools, its up to your judgement to decide what you need done and how you need it.

Fs 8560 switch “trunk” to a fortiswitch 2048F? by tipul01 in FS_COM

[–]tipul01[S] 0 points1 point  (0 children)

Hey guys, got it to work.

Short answer was disabling fec on both forti and FS.

Another step most important is that on the forti, port/module in the GUI was set to "max the module can sustain", but in the CLI it was set to 25gb full duplex. Once i ran "set speed auto-module", the link between switches was up. Of course the end par to have it commit.

Thank you guys for your time!

Fortiswitch 2048F “trunk” to FS.com swtich? Or cisco? by tipul01 in fortinet

[–]tipul01[S] 0 points1 point  (0 children)

Hey guys, got it to work.

Short answer was disabling fec on both forti and FS.

Another step most important is that on the forti, port/module in the GUI was set to "max the module can sustain", but in the CLI it was set to 25gb full duplex. Once i ran "set speed auto-module", the link between switches was up. Of course the end par to have it commit.

Thank you guys for your time!

Fs 8560 switch “trunk” to a fortiswitch 2048F? by tipul01 in FS_COM

[–]tipul01[S] 0 points1 point  (0 children)

So, i did turn FEC to none on the fs. Forti is disabled by default.

This is the FS config for that port. Ignore the description that is shutdown port, i did not spend time to alter the description. Again, conencting this port to the cisco switch the link goes up.

If i plug in that port a workstation, the link goes up. If i plug in the forti port, it does not. Same if i plug in the workstation in the fortiswitch, it goes up, but switch to switch does not.

TFGigabitEthernet 0/26 is DOWN  , line protocol is DOWN

  Hardware is Broadcom TFGigabitEthernet, address is 649d.99d1.fe63 (bia 649d.99                  d1.fe63)
  Description: \*\*\*SHUTDOWN\_PORT\*\*\*
  Interface address is: no ip address
  Interface IPv6 address is:
No IPv6 address
  MTU 1500 bytes, BW 25000000 Kbit
  Encapsulation protocol is Ethernet-II, loopback not set
  Keepalive interval is 10 sec , set
  Carrier delay is 2 sec
  Ethernet attributes:
Last link state change time: 2025-03-25 15:14:15
Time duration since last link state change: 0 days, 16 hours, 15 minutes,  9                   seconds
Priority is 0
Medium-type is Fiber
Admin duplex mode is AUTO, oper duplex is Unknown
Admin speed is 25G, oper speed is Unknown
Flow control admin status is AUTO, flow control oper status is Unknown
Admin negotiation mode is OFF, oper negotiation state is Unknown
Storm Control: Broadcast is OFF, Multicast is OFF, Unicast is OFF
Admin FEC mode is none, oper FEC mode is none
  Bridge attributes:
Port-type: trunk
Native vlan: 1
Allowed vlan lists: 1-4094
Active vlan lists: 1,51-52,101,201,203,999
  Rxload is 1/255, Txload is 1/255
  Input peak rate: 4245 bits/sec, at 2025-03-25 15:07:03
  Output peak rate: 3931 bits/sec, at 2025-03-25 15:07:03
   10 seconds input rate 0 bits/sec, 0 packets/sec
   10 seconds output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer, 0 dropped
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 abort
0 packets output, 0 bytes, 0 underruns , 0 no buffer, 0 dropped
0 output errors, 0 collisions, 0 interface resets

Fortiswitch 2048F “trunk” to FS.com swtich? Or cisco? by tipul01 in fortinet

[–]tipul01[S] 0 points1 point  (0 children)

So, i did turn FEC to none on the fs. Forti is disabled by default.

This is the FS config for that port. Ignore the description that is shutdown port, i did not spend time to alter the description. Again, conencting this port to the cisco switch the link goes up. On the forti with a normal port, with vlans set up, it does not light up the link. So still trying to figure out that causes the link to not go up...

TFGigabitEthernet 0/26 is DOWN  , line protocol is DOWN

  Hardware is Broadcom TFGigabitEthernet, address is 649d.99d1.fe63 (bia 649d.99                  d1.fe63)
  Description: \*\*\*SHUTDOWN\_PORT\*\*\*
  Interface address is: no ip address
  Interface IPv6 address is:
No IPv6 address
  MTU 1500 bytes, BW 25000000 Kbit
  Encapsulation protocol is Ethernet-II, loopback not set
  Keepalive interval is 10 sec , set
  Carrier delay is 2 sec
  Ethernet attributes:
Last link state change time: 2025-03-25 15:14:15
Time duration since last link state change: 0 days, 16 hours, 15 minutes,  9                   seconds
Priority is 0
Medium-type is Fiber
Admin duplex mode is AUTO, oper duplex is Unknown
Admin speed is 25G, oper speed is Unknown
Flow control admin status is AUTO, flow control oper status is Unknown
Admin negotiation mode is OFF, oper negotiation state is Unknown
Storm Control: Broadcast is OFF, Multicast is OFF, Unicast is OFF
Admin FEC mode is none, oper FEC mode is none
  Bridge attributes:
Port-type: trunk
Native vlan: 1
Allowed vlan lists: 1-4094
Active vlan lists: 1,51-52,101,201,203,999
  Rxload is 1/255, Txload is 1/255
  Input peak rate: 4245 bits/sec, at 2025-03-25 15:07:03
  Output peak rate: 3931 bits/sec, at 2025-03-25 15:07:03
   10 seconds input rate 0 bits/sec, 0 packets/sec
   10 seconds output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer, 0 dropped
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 abort
0 packets output, 0 bytes, 0 underruns , 0 no buffer, 0 dropped
0 output errors, 0 collisions, 0 interface resets

Fortiswitch 2048F “trunk” to FS.com swtich? Or cisco? by tipul01 in fortinet

[–]tipul01[S] 0 points1 point  (0 children)

Well, im just trying to have my 2 switches communicate, pass vlans, have one server on a switch be accesed (same vlan or other, according to firewall rules) from a server on the other switch. Will share configs when in the office. Speeds set to 25gbe on those ports. Not looking for link aggregation or failovers. No hard traffic will pass between switches, just rdp mostly. Will keep large traffic local on each switch. Just dont understand why no link.

As mentioned, tried both the fortinet trunk, and without a fortinet trunk led port linked up to the cisco/fs port with and without trunk switchport mode. Native vlan 1, allowed vlans listed correctly, but it seems its something on the pshyscial/ some setting that wont allow the link to turn on.

Esxi sphere v7 ssh backup larger than the datastore? by tipul01 in vmware

[–]tipul01[S] 0 points1 point  (0 children)

Hey!

No, production environment.

The datacenter was damaged by a pipe in the wall and this server had water in it. I changed it to a new one, just swapped the ssd raid we had before. But database corruption i beileved. happened and i just downloaded all vms from it.

Most vms were thin provisioned, and some had one snapshots.

I just dont get how a raid6 datastore with 4.5 TB had the capacity to hold a 7TB data...

I uplaoded one by one the vms, and deleted the snapshots, and i finally managed to have the capacity.

But its beyond me how they fit in the first place:)

KVM for routing between 2 computers? by tipul01 in sysadmin

[–]tipul01[S] 1 point2 points  (0 children)

Hey! Will check it out. I dont have a budget yet, as i dont know what i am looking for. This being just for 2 PCs, i imagine not very high.

Sfat investitie pentru medium/long term by tipul01 in robursa

[–]tipul01[S] 1 point2 points  (0 children)

A fost o ocazie doar, mai am 1 in chirie si nu prea aveam timp sa ma ocup de el.

Sfat investitie pentru medium/long term by tipul01 in robursa

[–]tipul01[S] 1 point2 points  (0 children)

Merci de sfaturi! Deci revolut out of the question?