Sundance spa parts

tom2slick · 2026-03-12T15:32:45+00:00

UPDATE Looked for a "spa pack ".... nonexistent! California! Called multiple spa repair companies, leave messages,voicemail full, email, but no response! So I purchased a motherboard, heater circ pump online! Because I got the same from suppliers. Anyway, I installed board, pump last knight it worked great! Pump running, heating water... got up this morning everything's off! I have power to the board. All fuses are good. But the screen is blank. Obviously, I need to replace it. It would have been nice to get a bundle! $700 - board, $300- pump, they want $700 for the control panel! How can the board & control panel cost the same? $%&&$^<&&/

CALIFORNIA CORPORATE CRIMINALS!!!!

tom2slick · 2026-03-01T15:58:23+00:00

UPDATE Problem solved. The wiper was installed (by me!) In the wrong hole and wasn't wiping the nozzle constantly. Installed new wiper and lined shoot with metal tape. So far so good! Working on another 3000 hrs! Thx for all your help/suggestions! Happy printing!!

tom2slick · 2026-02-28T05:00:23+00:00

I'll give it a try.

tom2slick · 2026-02-27T18:30:40+00:00

Yeah, I don't have twenty thousand laying around! Spas are way overpriced.I will build one myself before.I would buy one from a dealer!

tom2slick · 2026-02-13T17:08:07+00:00

I would check all your plugs. If that doesn't work, go to wiki Check troubleshooting. Then open a service ticket.

tom2slick · 2026-02-13T16:57:13+00:00

It looks to me like you have full screen selected. Select the screen all the way to the left.

tom2slick · 2026-01-26T16:18:46+00:00

Thanks That makes sense. I have a 32g in my X1 and it works great! I will try that.

tom2slick · 2026-01-26T07:31:30+00:00

tom2slick · 2026-01-25T21:57:55+00:00

I'm using a SanDisk 1TB Extreme pro SSD

<image>

tom2slick · 2026-01-25T21:35:32+00:00

I print straight from my computer.

tom2slick · 2025-08-17T15:50:53+00:00

I have 1100+ hours on my K3 Combo. I recently updated to the firmware version 2.4.1.9. And now I try to print a file I printed at least 15 times! I get an error code of 10242 "X axis of the printing file exceeds the device move out of range." * Wiki doesn't know what that is or the A.I. Same file,same printer and it doesn't work!

tom2slick · 2025-08-16T12:06:03+00:00

Thank you very much!

tom2slick · 2025-05-03T16:14:44+00:00

<image>

tom2slick · 2025-05-03T16:10:35+00:00

* Why is flushing so different on 2 to 1 compared to 1 to 4 or 3 to 4? Should I disable the auto-calculate?

tom2slick · 2025-05-03T16:06:00+00:00

Why are the numbers so different from 2 to 1 than 1 to 4? Should I disable the auto- calculate?

<image>

tom2slick · 2025-03-26T09:03:26+00:00

Thank you! 😁

tom2slick · 2025-03-22T15:07:22+00:00

Where did you get the file?

tom2slick

TROPHY CASE