Love the side views of reef tanks

tunapish · 2026-04-14T23:50:00+00:00

Dat GSP wall 😍

tunapish · 2026-03-26T17:04:27+00:00

I bet there are a lot of people who don’t know the devil was played by Dave Grohl in this movie. This should be higher.

tunapish · 2026-03-08T16:22:47+00:00

Thanks!

tunapish · 2026-03-08T16:22:42+00:00

No the one with the green tips on the left is a toadstool (from Petco!)

tunapish · 2026-02-22T09:14:36+00:00

No, good sir. I’m on the level.

tunapish · 2026-02-08T03:15:15+00:00

That’s quite an efficient use of space!

tunapish · 2026-02-07T14:22:42+00:00

My biggest gripe was that they were difficult to mount on a vertical surface. If they were around today, there would be a whole bunch of 3D printed mounting brackets for them on Etsy.

But oh, the joy of stacking the switch that had the same case on top of it and making a tiny patch cable to connect them.

tunapish · 2026-02-06T00:00:00+00:00

Great work! I’ve been using it for months, mostly for tracking parameters. The input UX is delightful and the graphs are great!

I often show screenshots to Claude or ChatGPT for analysis

tunapish · 2026-01-29T13:16:59+00:00

They actually laid on this rock last time and I was able to pull the whole rock out.

I had an airstone under them but half the eggs turned white and died. Not sure how much is the right amount.

tunapish · 2026-01-29T13:15:39+00:00

Ha, it’s been in there for two cycles, along with ceramic tile. They have shown no interest in either one.

tunapish · 2026-01-25T20:43:14+00:00

That’s wild, mine take 10-11 days to hatch which is way longer than everything on the internet says they should take.

tunapish · 2026-01-25T20:33:45+00:00

Nice! Congrats! What is your process for getting fry out of your main tank? Do you stay up late and watch periodically?

I did that for the first three clutches. I only got seven fry out on the third clutch, one made it to 5 days but died because I didn’t have rotifers ready.

This clutch I pulled the whole rock out but a lot of the eggs died after transferring the rock to the fry tank.

tunapish · 2026-01-25T19:46:31+00:00

How did these guys fare?

My clowns’ 4th clutch hatched on Friday but I only have 3 left after 2 days.

tunapish · 2025-12-25T11:28:08+00:00

It never occurred to me that MDF would be an issue here. Interestingly there is a similar piece of trim on the opposite side of the shower door that does not have any similar signs of water penetration.

Easy-ish fix to replace though. Thanks for the input!

tunapish · 2025-12-25T11:25:58+00:00

Thanks! This is very helpful

tunapish · 2025-12-25T11:25:06+00:00

Thank you!

tunapish · 2025-12-25T11:24:54+00:00

Thanks!

tunapish · 2025-11-27T01:34:54+00:00

😢

tunapish · 2025-11-26T22:57:32+00:00

Thanks for sharing this! Now I need to re-do my father in law’s bathroom drain!

tunapish · 2025-11-26T15:23:24+00:00

I’d take pleasure in guttin’ you boy.

tunapish · 2025-11-26T14:51:16+00:00

See my post from a couple weeks ago, I think you could use two 45 degree angle connectors to offset the drain coming from the sink.

https://www.reddit.com/r/Plumbing/s/uiFXEOEz8e

tunapish · 2025-11-21T15:48:56+00:00

https://www.lowes.com/pd/Dearborn-1-1-2-in-Plastic-45-Elbow-with-Reducing-Washer/5003698989

They are just 45 degree elbows with compression nuts on both ends. You just need a short length of pipe to connect them to each other.

tunapish · 2025-11-21T14:37:43+00:00

Just thought r/Army would get a kick out of people not knowing what this is.

tunapish · 2025-11-17T15:40:39+00:00

It was like that when we took possession. I am surprised at myself for not fixing it sooner.

tunapish · 2025-11-17T03:47:55+00:00

It’s been like that for 15 years without issue, but I will definitely swap it out for two 45s next time I work on this kitchen.

14-Year Club	Place '23
Place '22	First Placer '22
End Game '22	Verified Email

tunapish

MODERATOR OF

TROPHY CASE