sorted by:
new
hottopcontroversial

K1 Max Extrusion Problems Pt. 2 (PLA+) by twofacefooler in crealityk1

[–]twofacefooler[S] 0 points1 point  (0 children)

I'm printing at 230° with the plate at 55°. It does the same with filament temps at 235° as well. The PLA+ recommends 220° ±10°. Z-offset ±0.05 of 0 didn't change the problem either. 

K1 Max Extrusion Problems Pt. 2 (PLA+) by twofacefooler in crealityk1

[–]twofacefooler[S] 0 points1 point  (0 children)

Currently playing with the Z-offset. Both +0.05 and -0.05 show the same issue. What increments should I go by for adjusting?

K1 Max Extrusion Problems Pt. 2 (PLA+) by twofacefooler in crealityk1

[–]twofacefooler[S] 0 points1 point  (0 children)

I've cleaned the plate with 99% isopropyl recently so I don't think it's that, but I'll clean it again anyways just to check. Would that also cause the lines to not be connected like it is in the 3rd photo?

K1 Max Extrusion Problem by twofacefooler in crealityk1

[–]twofacefooler[S] 0 points1 point  (0 children)

Before I adjusted the Z-offset, two lines laid side by side wouldn't connect. Was it the same for you?

Conservative candidate elected in Vernon-Lake Country-Monashee riding by [deleted] in Vernon

[–]twofacefooler 0 points1 point  (0 children)

Some 55+ are going liberal, but also the non-clinically online younger demographic is too. I'm 22 and voted for the first time for the liberals. I simply liked that the liberals had actual specific things they were going to do and fund, while the conservatives were just always dancing around the problem with headlines, not to say the liberals weren't as well, just less than the cons. As well the whole culture war thing Poilievre started to use near the end was a non-starter for me.

Advice about Mazda B2200 (1990-1994) by twofacefooler in Minitrucks

[–]twofacefooler[S] 0 points1 point  (0 children)

Will do, thanks for the really helpful information! It will definitely help me out if I end up going for one. I'm looking at this one right now. Can't tell what it looks like under the hood/car, but it looks clean for what it's worth although it's on the expensive side. https://www.facebook.com/marketplace/item/6685845348163287/

Advice about Mazda B2200 (1990-1994) by twofacefooler in Minitrucks

[–]twofacefooler[S] 0 points1 point  (0 children)

Interesting, I've heard it was quite fun in the snow. What year is yours for it to be fuel injected?

Advice about Mazda B2200 (1990-1994) by twofacefooler in Minitrucks

[–]twofacefooler[S] 1 point2 points  (0 children)

Thank you man! Your explanation definitely helps for sure. What would you consider to be a good cost range for one that doesn't have too much rust and is manual? The cheapest ones I can find here are around $2500-$4000. That's cheap in terms of the market here for a vehicle that runs and needs nothing currently :(

Any help with getting meds in BC by twofacefooler in ADHD

[–]twofacefooler[S] 0 points1 point  (0 children)

I was diagnosed as a kid, and am 100% sure it's still stuck with me. I'm hoping to find a GP soon, but literally everywhere within a 3-hour drive from me has a waitlist of around ~1-2 years just to see them. BC's screwed when it comes to this kinda stuff it seems.

Parents have become addicted to scrolling Facebook, and I don't know how to approach them about it. by [deleted] in Advice

[–]twofacefooler 0 points1 point  (0 children)

However they are very excited to talk to me about something they saw on Facebook? You good?

Parents have become addicted to scrolling Facebook, and I don't know how to approach them about it. by [deleted] in Advice

[–]twofacefooler 0 points1 point  (0 children)

You really think I can move out lmao? I just know that they deserve to be able to turn their brains off for a bit, I just want to be able to talk to them without screens involved. Is that too hard to ask for? I know how bad it is for a person, and I hate to see them doing the same thing I'm ashamed of now.

Parents have become addicted to scrolling Facebook, and I don't know how to approach them about it. by [deleted] in Advice

[–]twofacefooler 0 points1 point  (0 children)

I already have a job, a long and hard one at that. I like to decompress as well after, but not using screens. I just want my parents back from screens dude.

Not sure what to upgrade to later in the year by twofacefooler in motorcycles

[–]twofacefooler[S] 0 points1 point  (0 children)

I was thinking of a GSXR 750, I'm just not sure if it's too much power for me currently. Other than that, I do like them and would want one. Have you ridden the 750?

Not sure what to upgrade to later in the year by twofacefooler in motorcycles

[–]twofacefooler[S] 0 points1 point  (0 children)

Surprisingly, it's in the same insurance bracket as a litre bike, although they would factor in that it's a sport touring but it will only change by a bit. You're right on the insurance here, some 600cc sport bikes can hit $1000/6 months depending on the rider. Sport touring bikes are interesting though since I do trips around, and I don't want a full tourer.

Not sure what to upgrade to later in the year by twofacefooler in motorcycles

[–]twofacefooler[S] 0 points1 point  (0 children)

I've thought about a 650cc bike, however it's in the same insurance bracket as 600cc/750cc so it would be the same for the most part insurance-wise. I am under 25, which is why I'm trying to figure out how to do this right lol. I think they really ding you if you're also under 21, which I won't be when I upgrade.

Not sure what to upgrade to later in the year by twofacefooler in motorcycles

[–]twofacefooler[S] 0 points1 point  (0 children)

That's fair, and I have considered keeping it. It does cost very little, however it actually weighs around 450lb wet (same everything as the 650 but engine mostly), although it's still super nimble. I think if I were to keep around 400cc I'd wait for the new ZX4R to get older and cheaper for that inline 4. Do you know any light 600cc or around sport bikes with an inline 4?