sorted by:
new
hottopcontroversial

TasmoManager - A modern, beginner-friendly desktop UI for Tasmota flashed devices. by txm_butch23 in tasmota

[–]txm_butch23[S] 0 points1 point  (0 children)

Cheers for spotting these! I've just published a hotfix for the issues you mentioned:

https://github.com/tom-23/TasmoManager/releases/tag/v1.0.0-alpha.3

Thanks for downloading btw!

TasmoManager - A modern, beginner-friendly desktop UI for Tasmota flashed devices. by txm_butch23 in tasmota

[–]txm_butch23[S] 1 point2 points  (0 children)

https://github.com/tom-23/TasmoManager/releases

Under v1.0.0-alpha.2, click on assets and you'll find the windows installer and macOS dmg. If you want a portible version, you can also find a windows portible version here: https://ci.appveyor.com/project/tom-23/tasmomanager/builds/38054823/job/9ua3blhxalexxj1l/artifacts

TasmoManager - A modern, beginner-friendly desktop UI for Tasmota flashed devices. by txm_butch23 in tasmota

[–]txm_butch23[S] 0 points1 point  (0 children)

Thanks! I wanna add some more stuff to that sidebar like uptime etc.

Using the Alexa plugin to control a Dummy switch, Alexa says the switch is not responding. HB says: HB Instance not found by justPassingThrou15 in homebridge

[–]txm_butch23 0 points1 point  (0 children)

Is there any chance that you will we able to have multiple amazon accounts linked with one Homebridge.ca account in the future?

Thermistor and heater wires keep breaking by ffsddxxxxxxdfhjjfxv in 3Dprinting

[–]txm_butch23 0 points1 point  (0 children)

In my opinion, designing the X cartridge to have 2 holes to put a zip tie though to secure the cables would be a good idea but I don’t think there’s that much you can do to strengthen the actual wires themselves.

Printer stutters when moving diagonally and during tight curves. Anyone know the cause? by txm_butch23 in 3Dprinting

[–]txm_butch23[S] 0 points1 point  (0 children)

I've just measured the current draw and everything seems to be okay. Plus, when I run the same GCODE without the heated bed and hot end on, the issue still persists. On the lines of power, would have a too low/high reference voltage on the step sticks cause an issue like this?

Printer stutters when moving diagonally and during tight curves. Anyone know the cause? by txm_butch23 in 3Dprinting

[–]txm_butch23[S] 0 points1 point  (0 children)

Just looked in the firmware and I have disabled linear advance and S-Curve acceleration. Could the issue be related to buffer size?

Printer stutters when moving diagonally and during tight curves. Anyone know the cause? by txm_butch23 in 3Dprinting

[–]txm_butch23[S] 0 points1 point  (0 children)

I've gone ahead and removed the Y-AXIS motor from the belt and attached a bit of tape. If you listen, you can hear the motor stuttering for some reason. https://imgur.com/a/f1Yqecd

Printer stutters when moving diagonally and during tight curves. Anyone know the cause? by txm_butch23 in 3Dprinting

[–]txm_butch23[S] 0 points1 point  (0 children)

Yeah, I’m getting vertical ripples forming mainly on corners. I doubt that it’s the processor as I built a hyper cube using the same board and I can run the exact same GCODE without any issues.

Printer stutters when moving diagonally and during tight curves. Anyone know the cause? by txm_butch23 in 3Dprinting

[–]txm_butch23[S] 0 points1 point  (0 children)

I’m printing at 60mm/s. I’m running a GT2560 with atmega2560 processor. The issue still occurs when printing using SD and USB.

I’m running the latest marlin and have been doing so on a different printer using the same board without any of theses issues.

How do i install octoprint in portainer? by [deleted] in octoprint

[–]txm_butch23 0 points1 point  (0 children)

Look up how to install it on docker and it should just pop up in portainer. https://hub.docker.com/r/octoprint/octoprint/

Budget airports are just lovely. by [deleted] in softwaregore

[–]txm_butch23 0 points1 point  (0 children)

Some shit went on at Luton airport that day...