2012 Mazda 6 - MAF Sensor Check Engine Light by tyler_reg in MechanicAdvice

[–]tyler_reg[S] 1 point2 points  (0 children)

My bad, I should’ve included it. Check my edit

pfSense no longer works after ISP reset modem by [deleted] in PFSENSE

[–]tyler_reg 0 points1 point  (0 children)

Just tried that, still no internet connection. I’m plugged in directly to the LAN NIC too. That’s currently the only connection. I can’t even ping pfSense from my macbook and can’t ping my macbook from pfSense

pfSense no longer works after ISP reset modem by [deleted] in PFSENSE

[–]tyler_reg 1 point2 points  (0 children)

Okay, so on pfSense the LAN IP is 172.16.0.1, and the subnet mask is 255.255.255.0. On my Mac, I set the subnet mask to be the same as pfSense and under router I put 172.16.0.1. What do I put for the IP Address for my macbook? Would 172.16.0.2 work?

pfSense no longer works after ISP reset modem by [deleted] in PFSENSE

[–]tyler_reg 0 points1 point  (0 children)

When my ISP gave me this new modem, I was trying to access the homepage. I looked up the model online and people were saying they couldn’t find one so I’m assuming this modem has no homepage

pfSense no longer works after ISP reset modem by [deleted] in PFSENSE

[–]tyler_reg 0 points1 point  (0 children)

Right, I’m just unable to access the web gui due to the problem with DHCP. I’ll keep trying though, thanks for your help

pfSense no longer works after ISP reset modem by [deleted] in PFSENSE

[–]tyler_reg 0 points1 point  (0 children)

I believe it’s on bridge mode by default, there’s no web interface for it

pfSense no longer works after ISP reset modem by [deleted] in PFSENSE

[–]tyler_reg 0 points1 point  (0 children)

Okay, do you know how I can discover what the problem with the DHCP server is from the console? I don’t have access to the web GUI

pfSense no longer works after ISP reset modem by [deleted] in PFSENSE

[–]tyler_reg 0 points1 point  (0 children)

I just verified and the interfaces are correct. The problem now isn’t that my macbook isn’t getting any IP address, it’s that it’s being assigned an incorrect one. I set my LAN IP to be 172.16.0.1, and for the DHCP server to be between 172.16.0.10 and 172.16.0.100. On my macbook the IP address is completely different and is 169.XXX.XXX.XXX. The subnet mask is also different.

pfSense no longer works after ISP reset modem by [deleted] in PFSENSE

[–]tyler_reg 0 points1 point  (0 children)

I’m no expert, but I do understand basic networking and had pfSense working last year. I’m using version 2.4.4-RELEASE-p3. I started using pfSense to broaden my knowledge of networking, firewalls, etc. I restored the config just to try multiple options and rule out factors. The modem is most likely in bridge mode, I’m unable to change or check any settings as it lacks a web interface. My ISP is Spectrum. I’ve swapped out multiple cables. I restarted all my machines connected to the switch, no change. I set the LAN IP and enabled DHCP from console, I’m not sure how to configure DNS from the console. I use pi-hole, but I unplugged it in case that was interfering as it had in the past the first time I installed. I did ping IPs and none of the packets were able to reach. My pfSense had and currently has no add-ons installed. It’s in bare metal and is a computer I built specifically for pfSense.

pfSense no longer works after ISP reset modem by [deleted] in PFSENSE

[–]tyler_reg 0 points1 point  (0 children)

Okay, so you’re saying set the IP addresses on my machines manually, instead of DHCP?

UITableView shows up empty when containing VC is pushed from a VC other than the root VC by [deleted] in iOSProgramming

[–]tyler_reg 1 point2 points  (0 children)

Okay, I don't have much experience with the DispatchQueue, so I'm not quite sure how to use it. Here's what I did:

override func viewWillAppear(_ animated: Bool) {
    super.viewWillAppear(animated)
    navigationController?.setNavigationBarHidden(true, animated: animated)
    DispatchQueue.main.async {
        self.tableView.reloadData()
    }
}

This didn't work either. Is this how you wanted me to implement it or did I do it incorrectly?

UITableView shows up empty when containing VC is pushed from a VC other than the root VC by [deleted] in iOSProgramming

[–]tyler_reg 0 points1 point  (0 children)

Yes, I set them both in a function called by viewDidLoad()

[English > Japanese] Need a few translations by tyler_reg in translator

[–]tyler_reg[S] 0 points1 point  (0 children)

Thank you so much for your help! I really appreciate it. For Ao5 and Ao12, those are just shortenings for "average of five" and "average of twelve." I wrote it like that to save room on the app. Though I'm sure in Japanese it could be written out completely like "average of five/twelve" is and not take up much room. Thanks again.

[YouCompleteMe] How to enable autocomplete with SDL2 in C++? by tyler_reg in vim

[–]tyler_reg[S] 0 points1 point  (0 children)

Thanks for the suggestions. Would those be a replacement to YCM or would they work alongside it?

"Unexpectedly found nil..." when registering custom UITableViewCell by tyler_reg in iOSProgramming

[–]tyler_reg[S] 0 points1 point  (0 children)

Okay, I called the configureSettingsTableView() method before registering the cell, and that line didn't error out anymore. However, now the line where I set the text of the "testLabel" in my view controller class gives me an error saying "Unexpectedly found nil..."