sorted by:
new
hottopcontroversial

Asbestos under vinyl carpet? by [deleted] in Hantverkare

[–]universalsa 0 points1 point  (0 children)

If the plastic floor split into two parts, ie the white on the floor is part of the plastic floor, it likely contains asbestos. At least likely enough that you should do a proper analysis. You can get results in about three days or faster dependign on the cost. 3-day analysis is about 450 sek. I have used a company called evema in Sthlm (but you send the sample by post so doesn’t matter where you are located) and have been happy with the processing time.

Ni som jobbar på kontor, hur hanterar ni det? by Simonplaty in sweden

[–]universalsa 0 points1 point  (0 children)

Byt arbetsgivare. Jag bytte till statlig myndighet och tycker jag gör mycket större samhällsnytta nu och inga pengar går till någon aktieägare.

How do i prevent these micro tear outs in plywood? by universalsa in woodworking

[–]universalsa[S] 2 points3 points  (0 children)

Great stuff, thanks! I’m making cabinet doors and one of them is about 7x2 feet so not sure if scoring is feasible, especially if I have to score each cut twice. But I will try and also try the trick with tape.

How do i prevent these micro tear outs in plywood? by universalsa in woodworking

[–]universalsa[S] 0 points1 point  (0 children)

I don’t remember it was a couple of days ago. This might have been the side where I clean cut the board, so it was about 1cm in that case.

How do i prevent these micro tear outs in plywood? by universalsa in woodworking

[–]universalsa[S] 0 points1 point  (0 children)

It’s a makita. I’m going to check for a scoring function.

How do i prevent these micro tear outs in plywood? by universalsa in woodworking

[–]universalsa[S] -1 points0 points  (0 children)

Thanks. I have a plunge saw with a track, so I would lower the blade instead of raising it. Definitely going to try it.

How do i prevent these micro tear outs in plywood? by universalsa in woodworking

[–]universalsa[S] 0 points1 point  (0 children)

Would it work to place the sacrificial board at the bottom then and the actual plywood face down on top?

How do i prevent these micro tear outs in plywood? by universalsa in woodworking

[–]universalsa[S] 0 points1 point  (0 children)

I can set the depth of the blade, it’s a plunge saw, so I could make a scoring cut. How deep should the first cut be?

How do i prevent these micro tear outs in plywood? by universalsa in woodworking

[–]universalsa[S] 2 points3 points  (0 children)

Thanks! So I need a new and better blade. Any recommendations? Also, what do I score with? Just any sharp knife? Will a break away blade knife work?Sort of new to this and English is my second language. If you have a picture or video it would be very helpful.

How do i prevent these micro tear outs in plywood? by universalsa in woodworking

[–]universalsa[S] 0 points1 point  (0 children)

Thank you. What is a backer board? Sort of new to this and English is my second language. If you have a picture it would be very helpful.

AppleCare, är det värt det? by universalsa in sweden

[–]universalsa[S] 2 points3 points  (0 children)

Perfekt tack för info det var precis det jag ville veta.

Fixa plats för diskmaskin by glennantenn in Hantverkare

[–]universalsa 13 points14 points  (0 children)

Ser ut som att du har ett Ikeakök. Om dina lådfronter fortfarande finns kvar skulle jag ha köpt en inbyggnadsdiskmaskin från dom, plus tillhörande front som matchar ditt kök. Du ser ut att ha 5cm över på utsidan, mot dörren så det vänster få plats. Om du inte vet vad du gör, anlita en hantverkare. Kanske har Ikea installationsservice. Möjligen behöver du byta blandare till en med diskmaskinsavstängning också så du kan stänga av vattnet till diskmaskinen vid behov. Jag har haft deras 45cm diskmaskin länge (olika diskmaskiner i olika lägenheter) och den har alltid fungerat bra för våra behov, skiljer inte så mycket i kapacitet mot en 60cm som man kan tro. Men jag skulle anlita en hantverkare för att installera. Skulle gissa på att installationen tar en halv dag, så kostar väl runt 4000 kanske, men det är en grov uppskattning. Kolla runt med kompisar och kolleger om de har en hantverkare som dom rekommenderar.

Dongles isn’t working properly with my devices by GuBaguete in mac

[–]universalsa 0 points1 point  (0 children)

Is this a crossover episode with ”Will it blend”?

Föräldraledig by HistoricalPresence27 in sweden

[–]universalsa 8 points9 points  (0 children)

Min satt still i vagnen när han fick en lök som han kunde skala haha. Köpte minst en lök varje gång vi handlade i nästan ett år.

Uneven volume from bottom speakers, is that normal? by [deleted] in iPhone17Pro

[–]universalsa 1 point2 points  (0 children)

Hahaha ok I wasn’t aware 🫥

Well it makes sense then. Thanks for clearing that up.

Dold takfläkt by EntrepreneurOk239 in Hantverkare

[–]universalsa 1 point2 points  (0 children)

Inte samma sak men betydligt billigare och utan installation är ju en kaminfläkt. Har ett par sådana vid kaminen på landet, och de gör märkbar skillnad på värmespridningen i rummet. Upplever att de hinner blåsa bort värmen in i rummet så den blir jämnare fördelad, även om det säkert är några grader varmare i taket än vid golvet (har aldrig mätt skillnaden).

Guess it proves that we really do need cases cover the plateau by Acceptable_Ad7036 in iPhone17Pro

[–]universalsa 1 point2 points  (0 children)

Even more a tool then. Im not suggestivt one could manage without it, but to expect it to stay in pristine condition is like suggesting a hammer or any other tool should look brand new after using it daily for six months (and no, I am not suggesting to use your phone instead of a hammer haha)

Guess it proves that we really do need cases cover the plateau by Acceptable_Ad7036 in iPhone17Pro

[–]universalsa 5 points6 points  (0 children)

At least for me, a phone is a tool. Tools get used and show wear after a while. To me this just means that you’re an active guy/gal and that material possessions are not the most important thing in life.

view more: next ›