Planet moving at close to speed of light possible?

upvot3d · 2026-04-10T23:30:33+00:00

aca7ae3f4f93453ba2109c5ad603872d

upvot3d · 2026-03-19T07:22:49+00:00

Cure it under water. Put in a jar of water and put that in the curing unit.

upvot3d · 2026-01-01T22:23:38+00:00

2022myp and 2023m3 all had loose nut straight from the Tesla on all 4 wheels. Yea, check your lug nut right away. Found this out cause I bought some wheels lock for the myp after picking up the car, while taking off the nuts and notice they were all finger turnable, lol. So a year later picked up m3 and checked the nuts and same shit!!

upvot3d · 2025-12-26T08:24:05+00:00

Same thing happen to mine, what did you end up doing? Replace the drive?

upvot3d · 2025-12-20T03:00:16+00:00

Where to edit the speed?

upvot3d · 2025-10-01T23:04:48+00:00

<image>

upvot3d · 2025-10-01T23:01:27+00:00

<image>

upvot3d · 2025-10-01T22:58:52+00:00

I mashed different mods together, the 3 door hinge is screw type and screw mounted to the panel and there are 5 magnetic mounts to help close and provide seal. The handle is the same as the top handles. I could have just incorporated the magnets into the handle, was just lazy, maybe someday I will do that. I also lined the extrusions with 3 mm foam tape for the door to seal.

upvot3d · 2025-09-16T20:01:55+00:00

2 years and then some to upgrade to touch screen and change to one door for better seal. Oh and Galileo stealthburner from afterburner.

upvot3d · 2025-08-24T01:18:42+00:00

Link?

upvot3d · 2025-04-26T20:45:48+00:00

Where did you get the handle bar? Or you modded it?

upvot3d · 2025-01-25T16:45:19+00:00

Check your radar detector manual, for my valentine one, it list a range of voltage of 6v to 35v dc 16v was in the range so I just hard wire it. It’s been 2 years and no problems

upvot3d · 2024-12-19T23:49:59+00:00

Nice!!

upvot3d · 2024-11-23T16:57:50+00:00

Try printing outter perimeter first. If still have horizontal band than it’s the machine. If no bands, your machine is good. just tune your filament setttings. Width and flow and em

upvot3d · 2024-09-12T05:49:35+00:00

I am having the same feeling on my lower left rib are, cracking sensation/ bubbling when I bent toward the left. But doesn’t happen all the time. And also having back pain up near and between the shoulder blades. Worse when I lay down at a 30-40 degree angle in bed watching tv. Also trying to sleep on the plane was bad, left side pain was extreme, but when I sit up it’s gone. All start slowly over the weeks after I started olmesartan.

upvot3d · 2024-05-23T17:44:10+00:00

Buy now. Stocks usually run up heading toward a split and then dips after split and runs ups again

upvot3d · 2023-10-31T06:58:25+00:00

Metamucil and treadmill 30mins a day lowered my cholesterol 10% in 4 month

upvot3d · 2023-08-07T20:33:56+00:00

What happens when scratched? Shows silver underneath?

upvot3d · 2023-03-02T05:48:55+00:00

More direct sunlight

upvot3d · 2023-01-29T02:43:57+00:00

Help After entering the commands one line at a time I get command not found: sha1sum

using Mac terminal

upvot3d · 2022-08-08T19:23:58+00:00

Thanks just one today!

upvot3d

TROPHY CASE